JMA M-FR1 Manual De Instrucciones página 28

NICE remote controls can be synchronised either remotely or
directly on the receiver. In addition to the rolling code versions,
the BIO version and the regenerative reception versions of the
VERY and FLO models must be synchronised in these devices.
BIO remote control and FLO-R, VERY and SMILO rolling code
models
Remote synchronising procedure
1. Stand near the receiver and press and hold the button on
the device you wish to synchronise for at least 5 seconds and
then release.
The LED on the receiver will flash and then remain steady.
2. Slowly press the first button on the already synchronised
remote control 3 times and then once more on the new device.
The new remote control is now synchronised. Wait 15 seconds
before testing.
Direct synchronisation procedure on the receiver
1. Open the receiver and press the button on the circuit board
for around 3 seconds until the LED light up.
2. Within the next 10 seconds, press the button on the remote
control to be synchronised for 2 seconds.
The new remote control is now synchronised. Wait 15 seconds
before testing.
VERY RESONADOR REMOTE CONTROL
Attention: the position of the 10 receiver switches must be
known to synchronise this device.
Remote synchronising procedure
1. Press the 2 buttons on the remote control to be synchronised
simultaneously.
The LED will light up steady.
2. The 10 codes must be entered within a period of 5 seconds.
To do so, take the following steps.
3. Press the first button (top) if the switch is set to ON and the
second if it is set to OFF. Press 10 times for the 10 codes.
ATTENTION
Master BIO and VERY RESONADOR remote controls must be
synchronised directly, but this is not necessary for copies of an
already synchronised device.
SYNCHRONISING NORTON ROLLING CODE REMOTE
CONTROLS
NORTON rolling code remote controls are synchronised using
the same procedure as for JMC devices.
There are 3 synchronisation procedures for these devices.
PIN-MODE remote synchronising procedure
The following procedure must be applied if the receiver bears
the words PIN-MODE:
1. Stand near the receiver and use a pointed object to press
the pushbutton at the rear of the remote control you wish to
synchronise.
The receiver will emit a long beep, indicating that the device
has been successfully synchronised.
Remote synchronisation procedure using the original remote
control
1. Stand near the receiver and use a pointed object to press
the pushbutton at the rear of the synchronised remote control.
The receiver will emit a beep, indicating that it has switched to
synchronisation mode.
28
2. Within 10 seconds of the beep, press the button on the devi-
ce to be synchronised.
The receiver will emit another short beep to indicate that the
remote control has been synchronised.
If the receiver fails to synchronise the device (does not emit
the short beep) it may mean that the memory is full and the
remote control cannot be synchronised without the installer's
permission.
3. After 10 seconds the receiver will exit synchronisation mode
and emit 2 short beeps.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch or pushbutton labelled
"PROG".
2. Press the button or turn on the switch.
The receiver will emit a beep and the LED will light up. From
this point, follow the previous procedure from step 2 above.
SYNCHRONISING NOVOFERM ROLLING CODE REMOTE
CONTROLS
The Novoferm remote control can only be synchronised directly
on the receiver.
Direct synchronisation procedure on the receiver
1. Open the receiver and press the button located inside until
the LED begins to flash.
2. Then press the button on the remote control and hold for
approximately 3 seconds until the LED begins to flash quickly.
Take the following steps if the facility has a ceiling-mounted
motor.
SYNCHRONISING PRASTEL ROLLING CODE REMOTE
CONTROL
PRASTEL remote controls can be synchronised either directly
on the receiver or remotely using a remote control already syn-
chronised with the receiver.
Remote synchronisation procedure
1. Stand near the receiver (1-2 metres) with the synchronised
device.
2. Press and release buttons 1 and 2 simultaneously.
3. The LED on the remote control will light up after two seconds
and turn off.
4. When the LED on the remote control lights up again, simul-
taneously press buttons 1 and 2 and hold until the LED begins
to flash.
5. When the LED stops flashing the remote control will activate
the synchronisation mode of the receiver.
6. The receiver will remain in synchronisation mode for around
10 seconds.
7. Press one of the buttons on the remote control to be syn-
chronised.
8. The receiver will save the code.
Direct synchronisation procedure on the receiver
1. Connect the receiver to the power supply.
2. Press the ENTER RADIO button. All the red LEDS will light
up for 2 seconds, after which only the first LED will remain lit.
" "
3. Press the SET button repeatedly to select the relay you
wish to associate with the transmission.
4. Press the desired button to transmit the code. Each button