Synchronising Go Rolling Code Remote Con- Trols - JMA M-FR1 Manual De Instrucciones

the code. The indicator LED will turn off.
5. Press the button on the remote control again. The door
should move.
6. Press the button on the remote control again. The door
should stop moving.
SYNCHRONISING GENIUS ROLLING CODE REMOTE
CONTROLS
GENIUS remote controls can be synchronised either directly on
the receiver or remotely using a remote control already syn-
chronised with the receiver.
Remote synchronising procedure
1. Press and hold buttons P1 and P2 on the remote control alre-
ady synchronised in the facility for at least 5 seconds.
2. Within 10 seconds, press the same button on the remote
control already synchronised in the facility as the one you wish
to synchronise.
3. The receiver will enter synchronisation mode and the LED for
the active channel will light up steady.
4. Press the button you wish to synchronise on the new remote
control.
5. Repeat Step 4 if you wish to add more remote controls.
6. Wait for 10 seconds for the receiver to exit synchronisation
mode.
7. Repeat the process for the other channel.
Direct synchronisation procedure on the receiver
1. Press the button on the receiver for the channel you wish to
synchronise - SW1 to synchronise CH1 and SW2 to synchronise
CH2. Either LED 1 or LED 2 will light up steady indicating that
the receiver is in synchronisation mode.
2. Within 10 seconds press and hold the button you wish to
synchronise on the remote control for at least 1 second.
3. If synchronisation is successful, the LED will flash a couple
of times.
4. Repeat the process from Step 2 to synchronise additional
remote controls.
5. The receiver will automatically exit synchronisation mode 10
seconds after the last synchronisation.
SYNCHRONISING GIBIDI ROLLING CODE REMOTE CON-
TROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the programming button on the
circuit board.
2. Press it briefly.
The receiver LED will flash.
3. Within 10 seconds, press the button of the remote control
you wish to synchronise.
The receiver will automatically exit synchronisation mode after
a short time.
SYNCHRONISING GO ROLLING CODE REMOTE CON-
TROLS
The GO remote control is synchronised directly with the recei-
ver the first time the button is pressed. However, this option
is disabled on some models, which must be synchronised ma-
26
nually.
GO remote control manual synchronisation procedure
1. Open the receiver and locate a switch or pushbutton labelled
"PROG".
2. Press the button or turn on the switch.
3. Within ten (10) seconds of the beep, press the button on the
device to be synchronised.
The receiver will emit another short beep to indicate that the
remote control has been synchronised.
If the receiver fails to synchronise the device (does not emit
the short beep) it may mean that the memory is full and the
remote control cannot be synchronised without the installer's
permission.
4. After 10 seconds the receiver will exit synchronisation mode
and emit 2 short beeps.
Observations
If the procedure fails, it may mean that the receiver memory is
full and impedes synchronisation of new devices without the
installer's permission.
SYNCHRONISING JCM ROLLING CODE REMOTE CON-
TROLS
The JCM rolling code remote control synchronisation procedure
is identical for all models except the 868 MHz.
There are 3 synchronisation procedures for these devices.
PIN-MODE remote synchronising procedure
The following procedure must be applied if the receiver bears
the words PIN-MODE:
1.
Stand near the receiver and use a pointed object to press the
pushbutton at the rear of the remote control to be synchronised.
The receiver will emit a long beep, indicating that the device
has been successfully synchronised.
Remote synchronisation procedure using the original
remote control
1. Stand near the receiver and use a pointed object to press
the pushbutton at the rear of the synchronised remote control.
The receiver will emit a beep, indicating that it has switched to
synchronisation mode.
2. Within 10 seconds of the beep, press the button on the devi-
ce to be synchronised.
The receiver will emit another short beep to indicate that the
remote control has been synchronised.
If the receiver fails to synchronise the device (does not emit
the short beep) it may mean that the memory is full and the
remote control cannot be synchronised without the installer's
permission.
3.
After 10 seconds the receiver will exit synchronisation mode
and emit 2 short beeps.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch or pushbutton labelled
"PROG".
2. Press the button or turn on the switch.
The receiver will emit a long beep and the LED will light up.
From this point, follow the previous procedure from step 2
above.