Synchronising Came Rolling Code Remote Con- Trols - JMA M-FR1 Manual De Instrucciones

If the procedure fails, it may mean that the receiver memory is
full and impedes synchronisation of new devices without the
installer's permission.
SYNCHRONISING CAME ROLLING CODE REMOTE CON-
TROLS
CAME ATO remote controls can be synchronised either directly
or remotely by taking the following steps.
Synchronisation procedure using the receiver
1. Press the button of the desired channel on the receiver for
2 seconds.
2. The LED on the receiver will flash.
3. Press the button of the same channel on the remote control
to be synchronised. Press the button for the same channel on
each remote control in turn if you wish to synchronise more
than one device.
4. The LED on the receiver will change to steady each time a
button is pressed.
5. Repeat the process for the other channel.
Remote synchronising procedure
1. Press the button of the desired channel on the remote control
for 15 seconds.
2. The LED on the receiver will flash.
3. Press the button of the same channel on the remote control
to be synchronised. Press the button for the same channel on
each remote control in turn if you wish to synchronise more
than one device.
4. The LED on the receiver will change to steady each time a
button is pressed.
SYNCHRONISING CARDIN ROLLING CODE REMOTE
CONTROLS
Cardin remote controls can be synchronised either directly on
the receiver or remotely using a remote control already syn-
chronised with the receiver.
Remote synchronising procedure
1. Stand near the receiver with the remote control to be sy-
nchronised and another remote control already synchronised
with the receiver.
2. Using a pointed tool or a paper clip, press the key hidden
in the hole on the coloured front part of the original remote
control.
3. The receiver will emit a short beep.
4. Then press any button on the remote control already synchro-
nised in the facility.
5. The receiver will emit another short beep to indicate that it
has entered synchronisation mode and will remain in this sta-
tus for a maximum of 5 seconds.
6. Finally, press the button of the device to be synchronised.
7. The receiver will emit two short beeps to indicate that the
remote control has been synchronised correctly.
Additional remote controls may be synchronised by pressing
the respective buttons within 5 seconds of the previous action.
Direct synchronisation procedure on the receiver without dis-
play
"
1. Press and hold the MEMO
2. The green LED on the receiver will flash slowly.
"
button on the receiver.
3. Press the button on the remote control to be synchronised.
4. The LED will turn off.
" "
5. Release the MEMO button and the button on the remote
control.
6. The LED on the receiver will resume flashing.
7. Press the button on the remote control to be synchronised
again.
8. The LED will turn off to confirm that the device is synchro-
nised.
" "
9. Press the SET button repeatedly to select the relay you
wish to associate with the transmission.
Repeat the operation for all the buttons (channels) and all re-
mote controls you wish to synchronise.
SYNCHRONISING CARDIN S435 ROLLING CODE REMOTE
CONTROLS
The CARDIN S435 remote control can only be synchronised di-
rectly on the receiver.
Synchronisation procedure using the receiver
" " "
1. Press the P1 or MEMO
ver) button on the receiver.
2. The receiver LED will flash.
3. Press the button of the channel to be synchronised on the
receiver.
4. The LED will flash faster once it has been synchronised.
5. Repeat the process for the other channel.
SYNCHRONISING CELINSA ROLLING CODE REMOTE
CONTROLS
CELINSA receivers can be synchronised either remotely or di-
rectly on the receiver.
Remote synchronising procedure
1. Stand near the receiver and press and release the button at
the rear of the master remote control.
The receiver will emit a beep, indicating that it has switched to
synchronisation mode.
2. Within 5 seconds, press the button of the device to be sy-
nchronised.
The code is now stored in the receiver memory.
Wait for 30 seconds until the receiver emits two beeps, indica-
ting that it has exited the synchronisation mode.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch with 3 positions (A,
B and C). Position A is for synchronising remote controls while
B is for deleting them. Set the switch to A with extreme care.
The receiver is now ready to synchronise new remote controls.
2. Press the button of the device to be synchronised.
The receiver will store the code.
3. Synchronisation has been successfully performed. Repeat
step 2 for each additional remote control you wish to synchro-
nise. Otherwise, return the switch on the receiver to the neutral
position (C).
Take special care to set the switch to C and not to B. The latter
position would cause the codes of all remote controls synchro-
nised with the receiver to be deleted.
ATTENTION
"
(depending on the type of recei-
23