Replacement Parts - Eaton Pauluhn ZPLA Serie Manual Del Usuario

Ocultar thumbs

Contenido

página de 16

/ 16
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

MAINTENANCE GENERAL

Perform visual, electrical and mechanical inspections on a regular basis.

The environment and frequency of use should determine this. However,

it is recommended that checks be made at least once a year. We

recommend an Electrical Preventive Maintenance Program as described

in the National Fire Protection Association Bulletin NFPA No. 70B:

Recommended Practice For Electrical Equipment Maintenance (www.

nfpa.org).

The lens should be cleaned periodically to ensure continued lighting

performance. To clean, wipe the lens with a clean, damp cloth. If this is

not sufficient, use a mild soap or a liquid cleaner such as Collinite NCF or

Duco #7 . Do not use an abrasive, strong alkaline, or acid cleaner. Damage

may result.

Visually check for undue heating evidenced by discoloration of wires or

other components, damaged parts or leakage evidenced by water or

corrosion in the interior. Replace all worn, damaged or malfunctioning

components, and clean gasket seals before putting the luminaire back into

service.

Electrically check to make sure that all connections are clean and tight.

Mechanically check that all parts are properly assembled.

Check and re-torque all mounting hardware.

To prevent heat build-up, remove dust from the LED housing using a soft

brush or air pressure.

DRIVER REPLACEMENT INSTRUCTIONS

Based on the electrical ratings marked on the luminaire housing, one

of the following LED driver replacement kits by Eaton's Crouse-Hinds

is suitable. Check and verify which particular driver is provided based

on the catalog number, and order the exact replacement driver kit from

Eaton's Crouse-Hinds. Prior to installation, ensure the same model

number, voltage and amperage ratings for replacement match the original

driver ratings that came with the fixture.

Driver Model

Catalog Number

Number

EUC030S050DTM

ZPLA2-UNV1-DRIVER KIT

EUC060S105DTM

ZPLA4-UNV1-DRIVER KIT

Be sure to de-energize the luminaire before performing any maintenance.

Driver replacement requires removal of the driver cover (see Figure 13).

Open the threaded wiring access cap (see Figure 8) and allow the cap to

hang by the lanyard.

Disconnect the input wires (line in, neutral and ground).

Disconnect the conduit or fittings from the driver cover entries.

7 .

Remove the ten (10) socket head cap screws and lock washers from the

driver cover using a 5mm hex wrench or bit.

Ensure all driver cover screws have been removed.

Remove the driver cover.

10. Disconnect the input and output leads of the old driver

(see Figure 13).

11.

Remove the two (2) screws that secure the driver;

remove the old driver.

12. Unscrew the ground screw with a hex head bit, remove

the terminal ring and then remove the driver.

13. Remove thermal pad associated with old driver.

14. Replace with the new driver kit supplied by Eaton's Crouse-Hinds.

15. Peel off one side of the thermal pad and stick it to the bottom of the new

driver supplied by Eaton's Crouse-Hinds. After peeling off other side of

thermal pad, assemble the driver onto the housing. Assemble the ring

terminal, attached the ground wire of the driver with the ground screw,

and screw it in.

16. Reconnect output wires per wiring diagram. Ensure that the positive (+)

and negative (-) leads of the drivers are connected per the wiring diagram.

17 .

Re-install the new driver into the luminaire, ensuring that the driver is in

All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or completeness thereof are not

guaranteed. In accordance with Eaton's Crouse-Hinds Division's "Terms and Conditions of Sale," and since conditions of use are outside our control, the purchaser should determine

the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith.

Electrical Ratings Marked On

Compatible

Luminaire Housing

Fixture

120-277 VAC

50/60

ZPLA2-UNV1

127-300 VDC

50/60

120-277 VAC

50/60

ZPLA4-UNV1

127-300 VDC

50/60

Eaton's Crouse-Hinds Division

1201 Wolf Street Syracuse, NY 13208 • U.S.A.

direct contact with the luminaire housing and no wires are being pinched

between the driver and the housing. Secure with two (2) screws and

tighten to 6 in.-lbs. (0.7 N-m).

18. Ensure that output wires to LED boards are tied neatly next to the driver

and the input and dimming wire leads are tied neatly together (see Figure

13).

19. Reinstall the driver cover, ensuring no wires are being pinched between

the driver cover and the luminaire housing.

20. Re-install the ten (10) socket head cap screws and lock washers from the

driver cover using a 5mm hex wrench or bit.

21. Replace any damaged or missing cover screws. Use only alloy steel M6-

1.5 x 20mm screws.

22. Tighten cover screws in a criss-cross pattern and torque to 45 in.-lbs.

23. Reconnect the conduit or fittings to the driver cover entries.

24. Reconnect input wires per wiring diagrams.

25. Re-install threaded access cap (see "Wiring the Lighting Fixture").

Figure 12

PAINT SHIELD INSTALLATION INSTRUCTIONS

ZPLA PS2 and ZPLA PS4 accessories are paint shields that can be installed by

the

customer over the lens of the ZPLA to minimize paint overspray accumulation

on the light emitting surface.

Ensure all previous installation steps have been followed.

Locate the shield over the light emitting surface with the open portion

facing the luminaire (see Figure 14).

Hook one side of the shield over the flange on one side of the luminaire

housing.

Push on the opposite side of the paint shield to snap it over the flange on

the luminaire housing.

Paint Shield