Makita DVC152L Manual De Instrucciones página 17

Troubleshooting for wireless activation function
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual,
d o not attempt to d ismantle t h e tool. I nstea d , ask Makita A ut h ori z e d S er v i c e C enters, al w a y s using Makita repla c e-
ment parts f or repairs.
State of abnormality
T h e w ireless ac tiv ation lamp d oes
not ligh t/ blink.
Cannot finish tool registration / can-
c elling tool registration suc c essf ully .
T h e c leaner d oes not run along w ith
th e sw itc h operation of th e tool.
T h e c leaner runs w h ile th e tool' s
sw itc h trigger is not pulled .
Probable cause (malfunction )
T h e w ireless unit is not installe d into t h e tool.
T h e w ireless unit is improperly installed
into th e tool.
T h e terminal of th e w ireless unit and / or
th e slot is d irty .
T h e w ireless ac tiv ation button on th e
tool h as not been push ed .
T h e stand -by sw itc h on th e c leaner is
not set to " A U T O " .
No pow er supply
T h e w ireless unit is not installe d into t h e tool.
T h e w ireless unit is improperly installed
into th e tool.
T h e terminal of th e w ireless unit and / or
th e slot is d irty .
T h e stand -by sw itc h on th e c leaner is
not set to " A U T O " .
No pow er supply
I nc orrec t operation
T h e tool and c leaner is aw ay f rom eac h
oth er ( out of th e transmission range) .
Before finishing the tool registration/
c anc ellation;
- t h e s w it c h trigger on t h e tool is pulle d or ;
- t h e po w er button on t h e c leaner is turne d on.
T h e tool registration proc ed ures f or th e
tool or the cleaner has not finished.
R ad io d isturbanc e by oth er applianc es
w h ic h generate h igh -intensity rad io w av es.
T h e w ireless unit is not installe d into t h e tool.
T h e w ireless unit is improperly installed
into th e tool.
T h e terminal of th e w ireless unit and / or
th e slot is d irty .
T h e w ireless ac tiv ation button on th e
tool h as not been push ed .
T h e stand -by sw itc h on th e c leaner is
not set to " A U T O " .
More th an 1 0 tools are registered to
th e c leaner.
T h e c leaner erased all tool
registrations.
No pow er supply
T h e tool and c leaner is aw ay f rom eac h
oth er ( out of th e transmission range) .
R ad io d isturbanc e by oth er applianc es
w h ic h generate h igh -intensity rad io w av es.
O th er users are using th e w ireless ac ti-
v ation of th e c leaner w ith th eir tools.
17 ENGLISH
Remedy
I nstall th e w ireless unit c orrec tly in th e tool.
G ently w ipe of f d ust and d irt on th e terminal of th e
w ireless unit and c lean th e slot of th e tool.
P ush th e w ireless ac tiv ation button on th e tool
briefly.
S et th e stand -by sw itc h on th e c leaner to " A U T O " .
S upply th e pow er to th e tool and th e c leaner.
I nstall th e w ireless unit c orrec tly in th e tool.
G ently w ipe of f d ust and d irt on th e terminal of th e
w ireless unit and c lean th e slot of th e tool.
S et th e stand -by sw itc h on th e c leaner to " A U T O " .
S upply th e pow er to th e tool and th e c leaner.
Push the wireless activation button briefly and perform
th e tool registration/ c anc ellation proc ed ures again.
G et th e tool and th e c leaner c loser to eac h oth er.
T h e max imum transmission d istanc e is approx i-
mately 1 0 m h ow ev er it may v ary ac c ord ing to th e
c irc umstanc es.
Push the wireless activation button briefly and
perf orm th e tool registration/ c anc ellation proc ed ures
again.
P erf orm th e tool registration proc ed ures f or th e tool
and th e c leaner at th e same timing.
Keep th e tool and th e c leaner aw ay f rom th e appli-
anc es suc h as W i-F i d ev ic es and mic row av e ov ens.
I nstall th e w ireless unit c orrec tly in th e tool.
G ently w ipe of f d ust and d irt on th e terminal of th e
w ireless unit and c lean th e slot of th e tool.
Push the wireless activation button briefly and make
sure th at th e w ireless ac tiv ation lamp is blinking in blue.
S et th e stand -by sw itc h on th e c leaner to " A U T O " .
P erf orm th e tool registration again.
I f more th an 1 0 tools are registered to th e c leaner,
th e tool registered earliest w ill be c anc elled
automatic ally .
P erf orm th e tool registration again.
S upply th e pow er to th e tool and th e c leaner.
G et th e tool and th e c leaner c loser to eac h oth er.
T h e max imum transmission d istanc e is approx i-
mately 1 0 m h ow ev er it may v ary ac c ord ing to th e
c irc umstanc es.
Keep th e tool and th e c leaner aw ay f rom th e appli-
anc es suc h as W i-F i d ev ic es and mic row av e ov ens.
T urn of f th e w ireless ac tiv ation button of th e oth er
tools or c anc el th e tool registration of th e oth er
tools.