Functional Description - Makita DTWA070 Manual De Instrucciones

A battery short can cause a large current
o , overheating, possible burns and even a
breakdown.
6 . Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ° C ( 122 ° F ) .
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
Be careful not to drop or strike battery.
8 .
9 . Do not use a damaged battery.
1 0. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
F or c ommer c ial transports e.g. b y t h ir d parties,
f or w ar d ing agents, spe c ial re q uirement on pa c k-
aging an d labeling must be obser v e d .
F or preparation o f t h e item being s h ippe d , c onsult-
ing an e x pert f or h a z ar d ous material is re q uire d .
P lease also obser v e possibl y more d etaile d
national regulations.
T ape or mask o f f open c onta c ts an d pa c k up t h e
batter y in su c h a manner t h at it c annot mo v e
aroun d in t h e pa c kaging.
1 1 . When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
1 2. Use the batteries only with the products
speci ed by Makita. I nstalling t h e batteries to
non-compliant products may result in a fire, exces-
si v e h eat, e x plosion, or leak o f ele c trol y te.
1 3. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
U se o f non-genuine Makita batteries, or batteries t h at
h a v e been altere d , ma y result in t h e batter y bursting
causing fires, personal injury and damage. It will
also v oi d t h e Makita w arrant y f or t h e Makita tool an d
c h arger.
Tips for maintaining maximum
battery life
1 . Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 ° C - 40 ° C ( 50 ° F - 104 ° F ) . Let
a hot battery cartridge cool down before
charging it.
Charge the battery cartridge if you do not use
4 .
it for a long period ( more than six months ) .
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge rmly hen installing or removing battery
cartridge. F ailure to h ol d t h e tool an d t h e batter y
cartridge firmly may cause them to slip off your hands
an d result in d amage to t h e tool an d batter y c artri d ge
and a personal injury.
Fig.1: 1. R e d in d i c ator 2. Button 3. Batter y c artri d ge
T o remo v e t h e batter y c artri d ge, sli d e it f rom t h e tool
w h ile sli d ing t h e button on t h e f ront o f t h e c artri d ge.
T o install t h e batter y c artri d ge, align t h e tongue on t h e
batter y c artri d ge w it h t h e groo v e in t h e h ousing an d slip
it into pla c e. I nsert it all t h e w a y until it lo c ks in pla c e
w it h a little c li c k. I f y ou c an see t h e re d in d i c ator on t h e
upper si d e o f t h e button, it is not lo c ke d c ompletel y .
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
y ou or someone aroun d y ou.
CAUTION:
Do not install the battery cartridge
forcibly. I f t h e c artri d ge d oes not sli d e in easil y , it is
not being inserte d c orre c tl y .
Tool / battery protection system
T h e tool is e q uippe d w it h a tool / batter y prote c tion s y s-
tem. T h is s y stem automati c all y c uts o f f po w er to t h e
motor to e x ten d tool an d batter y li f e. T h e tool w ill auto-
mati c all y stop d uring operation i f t h e tool or batter y is
pla c e d un d er one o f t h e f ollo w ing c on d itions :
Overload protection
W h en t h e batter y is operate d in a manner t h at c auses
it to d ra w an abnormall y h ig h c urrent, t h e tool automat-
i c all y stops w it h out an y in d i c ation. I n t h is situation, turn
t h e tool o f f an d stop t h e appli c ation t h at c ause d t h e tool
to be c ome o v erloa d e d . T h en turn t h e tool on to restart.
Overheat protection
W h en t h e tool / batter y is o v er h eate d , t h e tool stops
automati c all y . I n t h is situation, let t h e tool / batter y c ool
be f ore turning t h e tool on again.
Overdischarge protection
W h en t h e batter y c apa c it y is not enoug h , t h e tool stops
automati c all y . I n t h is c ase, remo v e t h e batter y f rom t h e
tool an d c h arge t h e batter y .
7 ENGLISH