Advice Regarding The First Wash Cycle; Technical Data; Assistance; Ecodesign Regulation - Indesit DSG 5741 Instrucciones De Uso

Anti-condensation strip
EN
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order
to protect it from any condensation which may form.

Advice regarding the first wash cycle

After the installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack, if any.
Immediately before the fist washing,
dispenser with water and add only then approximately 1
(see chapter entitled Rinse aid and refined salt)
kg of salt
The water may overflow: this is normal and is not a cause
for concern. Select the water hardness value
entitled Rinse aid and refined salt).
poured into the machine, the LOW SALT indicator light
switches off.
If the salt container is not filled, the water softener and
the heating element may be damaged as a result.

Assistance

Before contacting Assistance:
• Check whether the problem can be resolved using the
Troubleshooting guide (see Troubleshooting).
• Restart the programme to check whether the problem
has ceased to exist.
• If the problem persists, contact the Authorised
Technical Assistance Service.
Never use the services of unauthorised technicians.
Please have the following information to hand:
• The type of malfunction.
• The appliance model (Mod.).
• The serial number (S/N).
This information can be found on the appliance data plate
(see Description of the appliance) .

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a nor-
mal soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption
even further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W
Consumption data table for the main cycles
Standard conditions
Energy consumption
(kWh/cycle)
INTENSIVE 1,25
NORMAL 1,00
*
Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
**
Data is obtained by recording values when the appliance is operational and loaded with user crockery.
16
*
completely fill the salt
(see chapter
- After the salt has been
*
Water consumption
(l/cycle)
13
13
The machine has a buzzer/set of tones
dishwasher model
) to inform the user that a command has
been implemented: power on, cycle end etc.
The symbols/indicator lights/LEDs on the control panel/
display may vary in colour and may have a flashing or fixed
(depending on the dishwasher model)
light
*
The display provides useful information concerning the
type of wash cycle, drying/wash-cycle phase, remaining
time, temperature etc.
.

Technical data

*
Dimensions
Capacity
Water supply pressure
Power supply voltage
Total absorbed power
Fuse
**
User conditions
Duration Energy consumption
(min/cycle) (kWh/cycle)
150 1,05
115 0,90
(depending on the
.
width 45 cm
height 85 cm
depth 60 cm
10 standard place-settings
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
See appliance data plate
See appliance data plate
See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/EU Waste Electrical
and Electronic Equipment
(WEEE)
Water consumption Duration
(l/cycle) (min/cycle)
13 140
13 110