Intended Use - Makita DHS782 Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Blad e d iameter
Max . C utting d epth
No load speed
O v erall length
R ated v oltage
Net w eigh t
Due to our continuing program of research and development, the specifications herein are subject to change
w it h out noti c e.
Specifications and battery cartridge may differ from country to country.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est c ombinations, a c c or d ing to E P T A - P ro c e d ure 0 1 / 20 1 4 , are s h o w n in t h e table.
Applicable battery cartridge and charger
Battery cartridge
C h arger
Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
•
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
WARNING:
and chargers may cause injury and/or fire.

Intended use

The tool is intended for performing lengthways and
crossways straight cuts and miter cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine sa w bla d es, ot h er materials
c an also be sa w e d .
Noise
The typical A-weighted noise level determined accord-
ing to EN 6 2 8 4 1 -2- 5 :
Model DHS782
Sound pressure level (L
pA
Sound power level (L ) :
WA
Uncertainty (K) : dB(A)
Model DHS783
Sound pressure level (L
pA
Sound power level (L ) :
WA
Uncertainty (K) : dB(A)
NOTE: The declared noise emission value(s) has
been measure d in a c c or d an c e w it h a stan d ar d test
method and may be used for comparing one tool with
anot h er.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
e x posure.
at 0°
at 4 5 ° bev el
at 4 8 ° bev el
) : dB(A)
dB (A)
) : dB(A)
dB (A)
DHS782
BL 1 8 1 5 N / BL 1 8 20 / BL 1 8 20B / BL 1 8 30 / BL 1 8 30B / BL 1 8 4 0 /
BL 1 8 4 0B / BL 1 8 5 0 / BL 1 8 5 0B / BL 1 8 6 0B
D C 1 8 R C / D C 1 8 R D / D C 1 8 R E / D C 1 8 S D / D C 1 8 S E / D C 1 8 S F
WARNING:
WARNING:
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mine d a c c or d ing to EN 6 2 8 4 1 -2- 5 :
Model DHS782
Work mode: cutting wood
Vibration emission (a
Uncertainty (K) : . m/s
Work mode: cutting metal
Vibration emission (a
Uncertainty (K) : . m/s
Model DHS783
Work mode: cutting wood
Vibration emission (a
Uncertainty (K) : . m/s
Work mode: cutting metal
Vibration emission (a
Uncertainty (K) : . m/s
10 ENGLISH
DHS783
1 8 5 - 1 9 0 mm
6 0.0 - 6 2.5 mm
4 3.0 - 4 4 .5 mm
4 1 .0 - 4 2.0 mm
-1
6 ,000 min
34 8 mm
D .C . 36 V
4 .5 - 5 .1 kg
W ear ear protection.
The noise emission during actual
Be sure to identify safety measures
) : . m/s
2
or less
h,W
2
) : . m/s
2
or less
h ,M
2
) : . m/s
2
or less
h,W
2
) : . m/s
2
or less
h ,M
2