Maintenance And Care - Flex VC 6 L MC Instrucciones De Funcionamiento Originales

VC 6 L MC
Overview (Figure A)
1 ON/OFF switch
2 Head section
3 Storage location for crevice nozzle
4 Inlet opening
5 Dust bag
6 Wheel frame (optional)
7 Lock
8 Filter cleaning button
9 Mains cable
10 Blower opening
11 Storage location for nozzle pipe
12 Handle
13 Filter holder
14 Filter
15 Nozzle pipe
16 Air flow regulator
17 Hose
18 Connector
19 Upholstery nozzle
20 Brush nozzle
21 Dust bag
22 Crevice nozzle
23 Shoulder strap
Instructions for use
Before initial operation
Carefully read the safety instructions in this manual before

bringing the device into operation for the first time.
Unpack the power tool and accessories and check that no

parts are missing or damaged.
Accessories (Figure B)
The nozzles and accessories for the device are located in the
dust container for transport. To open the dust container, re-
lease the fasteners (1) and remove the head section (2). Re-
move the parts (3) and fit the head section again. Secure the
head section with the fasteners.
Transport trolley (Figure C)
The wheels of the transport trolley must be mounted as shown
before initial use. Insert the castor wheels and the rear wheels.
Using the dust bag (Figure D)
To remove the dirt/dust from the dust container without any
dust escaping, a disposal bag can be used.
Insert the bag in the dust container. Secure the box at the

front of the dust container in the ribs.
Inserting the hose (Figure E)
Insert the connector in the suction opening (3) for vacuum

cleaning operation. Use the blower opening (4) for blower
operation.
Insert the hose in the connection (1) and twist to lock (2).

Air flow regulator (Figure F)
The air flow can be controlled at the end of the hose by turning
the air flow regulator.
Using a suitable nozzle (Figure G)
All of the nozzles shown can be inserted in the nozzle pipe (1).
The nozzle pipe (3) can be removed for vacuum cleaning by
pressing the clips (1) and pulling out the nozzle (2).
Using the shoulder strap (Figure H)
To use the shoulder strap, insert the clasps in the fasten-

ers. Carry the vacuum cleaner as shown in figure I.
Switching on and off (Figure J)
The main switch of the device has two positions (ON/OFF). The
device is switched on and off by pressing the main switch.
Accessory container (Figure K)
All accessory parts can be stored conveniently on the device.
Troubleshooting
Motor stops:
A thermal overload protector will shut off the motor if the

motor temperature is too high. If this occurs, turn the switch
off. Wait 15-30 minutes for the motor to cool. Turn switch
on and resume operation.
Suction power is reduced:
The tank may be full and needs to be emptied.

The hose and nozzle may be clogged and need to be

cleaned.
Any of the above may be damaged and need to be re-

placed.
The filter may be clogged. Use the Filter Cleaning System

to clean the filter. Replace the filter or make sure the filter is installed properly.

The hose connection is loose and need to be tightened.

Static shocks:
If the environment is too dry, add moisture to air. If possi-

ble, use a humidifier.
In case the relative humidity of air is low, please note that

this situation will not have any effect on use of the vacuum
cleaner.

Maintenance and care

NOTE
This vacuum cleaner has an integrated thermal overload
protection feature to protect the motor against high tempera-
tures. This can occur under strenuous operating conditions. If
the motor switches off during operation, switch off the device
using the main switch and allow the motor to cool down for 15-
30 minutes. The device can then be switched back on again.
WARNING!
–
Before cleaning and performing maintenance work, switch
off the device and remove the mains cable if the device is
connected to a power supply.
–
Switch off the device before changing to a different
function.
–
Maintenance work may only be carried out on this device
by authorised customer service centres or specialists who
are familiar with the relevant safety regulations.
–
Observe the local safety regulations for portable,
commercially used equipment.
–
The manufacturer or an appointed person shall carry out a
technical inspection at least once per year. The filter is
inspected for damage, for example, and the air-tightness of
the device as well as correct operation of the controls are
checked.
14