Blender Safety; Important Safety Instructions - Hamilton Beach HBH750 Manual De Operación

Blender Safety

IMPORTANT SAFETY INSTRUCTIONS

WARNING –
When using electrical appliances, basic safety precautions should be
followed, including the following:
• Read the Operation Manual before using blender.
Keep Operation Manual handy.
• Before first use, wash container assembly in hot,
soapy water. Do NOT place in dishwasher.
• Plug into a grounded outlet.
• Do not remove ground.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before cleaning or servicing.
• To reduce risk of personal injury, unplug cord
from outlet when not in use, and before putting
on or taking off parts.
• Unplug the blender and inspect the power cord
insulation for cracks on a weekly basis. Refer to
"Technical Services" for repair or replacement.
• To protect against electrical shock, do not
immerse cord, plug, or blender base in water or
any other liquid.
• Do not spray the base with a high-pressure spray
gun.
• Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.
• Do not use appliance for other than intended use.
• Not intended for use by or near children.
• Children should be supervised to ensure they do
not play with the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical,
sensory, or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
• The use of accessory attachments not
recommended by the appliance manufacturer
may cause injuries.
• To reduce risk of personal injury and to prevent
damage to blender or container and cutter
assembly, DO NOT insert utensils into blender
container while operating blender.
• Do not store any kitchen utensils in the container
because the blender would be damaged if
inadvertently turned on.
• To prevent possibility of serious personal injury,
keep hands out of blender container while
operating blender. Always operate blender with
container cover in place.
• Avoid contacting moving parts. Switch off the
appliance and disconnect from power supply
before changing accessories or approaching parts
that move in use.
• Blades are sharp. Handle carefully.
• If cutter assembly blades are loose, discontinue
use immediately and replace container. Do not
attempt to repair or tighten cutter assembly.
– SAVE THESE IN STRUC TIONS –
2
GB
• Inspect container and cutter assembly daily. Do
not use broken, chipped, or cracked container.
Check cutter for wear, nicks, or broken blades. Do
not use broken, loose, or cracked cutting blades.
• Do not use outdoors.
• This appliance is intended for short periods of
operation, with a rated operating time of
2 minutes.
• Do not leave blender unattended while it is
operating.
• To prevent damage to blender, container, or
cutter assembly, DO NOT move or shake blender
while in operation. If blending action stops
during operation, turn blender OFF (O), remove
container from base, remove container cover,
and use a thin rubber spatula to push mixture
towards cutters.
• Hot liquids may push lid off jar during blending.
To prevent possible burns: Do not fill blender
jar beyond the 1 quart (1 liter) level. With the
protection of an oven mitt or thick towel, place
one hand on top of lid. Keep exposed skin away
from lid. Start blending at lowest speed.
• The blender is provided with a power switch/
circuit breaker on the side of the unit. If the motor
stops turning, reset the power switch.
• This blender's motor is provided with a thermal
overload protector. If the motor stops turning
during operation or will not restart, unplug and
allow to cool for 15 minutes. Plug unit back into
outlet and resume operation.
• The normal function of this product may be
disturbed by strong electromagnetic interference.
If this occurs, simply reset the product and
resume normal operation by following the
operation manual. If normal operation cannot be
resumed, place the product in a different location.
• Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions,
or is dropped or damaged in any manner. If
the supply cord of this appliance is damaged,
it must be replaced by the manufacturer or
its service agent or a similar qualified person.
Refer to "Technical Services" for instructions on
examination, repair, or electrical or mechanical
adjustment.
• UK ONLY: If fitted with a non-rewirable U.K. plug,
the 13 amp fuse approved by ASTA to be B.S.
1362 must be used. If you need a replacement
fuse carrier, it must be replaced with the same
colour coded carrier with the same markings.
Fuse covers and carriers can be obtained from
approved service agents.