Best IP29M Serie Instrucciones De Instalación página 15

23. OPERATION (
CONT
Grease filter maintenance indicator
• After 30 hours of operation, the grease filter maintenance icon (item 5 on control illustration) appears. This means filters need to be
cleaned.
• Once the grease filter cleaning is done, press on grease filter reset push-button to reset the filter maintenance timer.
Interface backlighting
• Off mode (Blower off, Particulates sensor and Air refresh modes disabled): Backlighting is off.
• Halogen lighting activated: does not affect backlighting.
• Blower turns on: Backlighting at maximum intensity.
• Particulates sensor and Air refresh mode activated: Backlighting at maximum intensity.
• Particulates sensor at sensitivity settings and Air refresh in activated mode: Backlighting at minimum intensity.
HEAT SENTRY™
This hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that will start or speed up the blower if it senses
excessive heat above the cooking surface.
• If blower is OFF—it turns the blower to speed 3 (blower speed icon shows H).
• If blower is ON—it turns the blower up to speed 3 (blower speed icon shows H).
NOTE: When Heat Sentry™ is activated, Air refresh mode and Particulate sensor are inactivated. Also, communication coming from
the LinkLogic® Module is disabled.
The HEAT SENTRY can start the blower during a range top fi re or other excessive heat situations even if the hood is turned off. In this
case, it is impossible to turn the blower OFF using control panel buttons. If you must stop the blower, unplug the blower power cord
(located behind the fi lters) from the hood by pulling on its 2-prong connector; do not pull on the wire.
• When the temperature level drops to normal, the blower will return to its original setting (blower speed icon will show the original
blower speed).
• To turn off the blower when Heat Sentry™ is activated, press and hold the blower push-button (item 2 on illustration) for more than
1 second.
LinkLogic® Network compatibility
Your IP29M Series range hood can be linked to LinkLogic network, if installed in your house.
L L L I
INK OGIC INKING NSTRUCTIONS
A. A " "
CTIVATE THE LINK MODE OF THE HOOD
Push the LinkLogic link mode push-button (item 4 on control illustration) for 2 seconds; the LinkLogic icon of the interface (item 11 on
control illustration) should be visible and backlighting is full intensity at that point.
L W R
INK FOR ALL EMOTE
R
OR EMOTE
A "L "
CTIVATE THE INK
Push the "link" button of the LinkLogic device for
a specific duration to activate its link mode
(see instructions of LinkLogic device).
S "A
TART THE UTO
Push the LinkLogic link mode push-button
(item 4 on illustration) to start the "Auto-Link" process,
flashing "A" should be visible (item 8 on control illustration)
on the interface until link is done.
NOTE: For some LinkLogic devices, no "A" will be flashing
because the linking duration is too short.
B. E
XIT LINK MODE OF THE HOOD
Press and hold LinkLogic link mode push-button (item 4 on control illustration) for 2 seconds to exit "link" mode. Link mode remains
activated for 4 minutes if no other operation is done.
' )
D
C , R C
ONTROL EMOTE ONTROL
B M
LOWER ODULES
L L
MODE OF THE INK OGIC DEVICE
-L "
INK PROCESS OF THE HOOD
L
Go back to the appropriate first step if another LinkLogic device
needs to be linked. Otherwise, to exit "link" mode, go to
WARNING
!
L
INK FOR
G
O TO STEP
(item 1 on illustration) to start the "Master Link" process,
flashing "L" should be visible (item 8 on control illustration)on
the hood interface, meaning that the hood is waiting for a
(see instructions of device for location) for a specific duration to
activate its Link mode. Wait for the "L" to disappear from the
L L
INK OF ANOTHER INK OGIC DEVICE
E
XIT LINK MODE OF THE HOOD
15
S S ™
MART ENSE OR
22 ( )
ON NEXT PAGE TO CONFIGURE
JUMPERS BASED ON BLOWER PERFORMANCE
S "M L "
TART THE ASTER INK
Push the LinkLogic master link mode push-button
SmartSense™ or Make-Up Air module to link.
A "L "
CTIVATE THE INK MODE OF THE
Push the "link" button of the LinkLogic device
hood interface to do next step.
.
M -U A M
AKE P IR ODULES
L L
INK OGIC BOARD
.
PROCESS OF THE HOOD
L L
INK OGIC DEVICE