McCulloch SUPERLITE 4528 Manual De Usuario página 11

Ocultar thumbs Ver también para SUPERLITE 4528:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 104
WARNING: If the cutting unit does not
stop when you adjust the idle speed,
speak to your nearest servicing dealer.
Do not use the product until it is correctly
adjusted or repaired.
Note: The idle speed is correct when the engine
operates smoothly in all positions. Refer to
data on page 13 for the recommended idle speed.
To clean the cooling system
The cooling system keeps the engine temperature
down. The cooling system includes the cooling fins on
the cylinder (A), the cylinder cover (B) and the air intake
through the crankcase (C).
(Fig. 30)
CAUTION: The air intake between the fuel
tank and crankcase is easily blocked by
leaves. Clean the air intake fully.
1. Clean the cooling system with a brush weekly or
more frequently if it is necessary.
2. Make sure that the cooling system is not dirty or
blocked.
To examine the spark plug
CAUTION: Always use the recommended
spark plug type. Incorrect spark plug type
can cause damage to the product.
Examine the spark plug if the engine is low on
power, is not easy to start or does not operate
correctly at idle speed.
To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
on page 13 . (Fig. 31)
Replace the spark plug if it is necessary.
To clean the air filter
Clean the air filter regularly from dirt and dust. This
prevents carburetor malfunctions, starting problems,
loss of engine power, wear to engine parts and more
fuel consumption than usual.
1. Remove the air filter cover (A). (Fig. 32)
2. Remove the air filter (B) from the filter frame.
3. Clean the air filter with warm soap water.
1255 - 002 - 08.09.2020
4. Make sure that the air filter is dry.
5. Apply oil to the air filter. Refer to
Technical
6. Clean the inner surface of the air filter cover. Use
To apply oil to the foam air filter
1. Put the foam air filter in a plastic bag.
2. Put the oil in the plastic bag.
3. Rub the plastic bag to supply the oil equally across
4. Push the unwanted oil out of the foam air filter while
To lubricate the gear housing
To clean and lubricate the blades
1. Clean the blades from unwanted materials before
Technical data
2. Lubricate the blades before long periods of storage.
Note: Speak to your servicing dealer for more
information about recommended cleaning agents and
lubricants.
To examine the blades
1. Remove the lubricant filler cap on the gear housing.
2. Make sure that the blades move freely. Put the
3. Examine the edges of the blades for damages and
CAUTION: An air filter that is used for a
long time cannot be fully cleaned.
Replace the air filter regularly and
always replace a defective air filter.
foam air filter on page 11 .
compressed air or a brush.
CAUTION: Always use McCULLOCH
special air filter oil. Do not use other types of
oil.
WARNING: Put on protective gloves. The air
filter oil can cause skin irritation.
the foam air filter.
in the plastic bag. (Fig. 33)
Use McCULLOCH special grease. Speak to your
servicing dealer for more information about
recommended grease.
Add the grease through the lubricant filler cap on the
gear housing. (Fig. 34)
CAUTION: Do not fill the gear housing fully.
and after you use the product.
combination wrench in the gear housing and turn
clockwise and counterclockwise. (Fig. 35)
deformation.
To apply oil to the
11
Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Ergolite 6028

Tabla de contenido