TESY ES/GCVM 50 EC Instrucciones De Uso página 27

is pressed, and if a button is pressed continuously, the
temperature will change gradually by 1°C. Few seconds
after the last pressing of any of the two arrows, the display
will show the actual temperature of the water. You can
always see the set temperature by pressing the i button.
•
"Weekly programmer" mode
By pressing the PROG button, except for the Manual
operation mode, you can choose one of the three pre-set
weekly programme modes, respectively P1, P2 or P3.
The programmes are factory-set, however you can make
changes to them as you wish.
Choose programme P1, P2 or P3. By pressing the i button
you can check which days of the week and which hours
the appliance will operate and will heat water. If you wish
to make changes to the programme that you have chosen,
press and keep pressed the PROG button to enter the
settings.
The first step is to select the days (or the day) of the week
which you will make changes to. The blinking day of the week Monday indicates that the appliance is expecting
your choice. Use the arrows > and < to move the marker
and confirm by pressing the OK button for each of the days
which you will change the programme for. You can confirm
only one day of the week or all the seven.
Note: The words ON and OFF on the display will
give you further information whether a particular
day of the week has been chosen to be changed or not
(ON – the day has been selected, OFF – the day has not
been selected).
The second step is to programme the hours in which the
electric heater will heat the water, i.e. it will operate. To
proceed with the second step, press the PROG button
(do not hold it pressed).
Note: If you hold the PROG button pressed, you
will leave the setting mode of the respective
programme. To go back you need to press and hold the
PROG button and to repeat the steps of choosing a day
(days) of the week.
English
To choose the hours in which the appliance will operate,
use the arrows > and < and OK. Below you can see an
example of an hour diagram similar to the one you can see
on the display showing when the appliance will operate
(ON mode) and when it will not operate (OFF mode):
Explanation of the markings:
- if the cell denoting a particular hour is filled, the
appliance will operate during this hour and it will heat
the water up to the set temperature
- if the cell denoting a particular hour is empty, the
appliance will not operate during this hour
Example: If we look at the hour diagram above we
should expect that the appliance will heat the water
from 4:00 to 6:00 and from 17:00 to 22:00. In the rest of
the time it will not operate.
Method for setting the hours for operation of the
appliance:
There is a separate cell for each hour of the day and
the night provided in the hour diagram. The numbers
underneath indicate the hours. The changing of the
status of each cell ("full" or "empty") is done by pressing
the OK button when the marker is on this cell. You can
move the marker using the arrows > and <. The words
ON and OFF on the display will also indicate the status
of the particular cell.
To make it easier, when you move on the hour scale, the
cells are filled up or emptied automatically based on the
last confirmed status.
The third step in setting the operation of appliance
for the week is to set the temperature of the water for
the respective time interval in the selected days of the
week. To proceed with the third step, press the PROG
button (do not hold it pressed). The marker is on the
first cell indicating the hour in which the appliance has
been set to operate and it is now expecting your setting
of the temperature of the water. You can select different
temperature for each hour from the time period that
the appliance has been programmed to operate. To
make the setting use > and < and confirm by OK. Each
time you confirm pressing the OK button, you move to
the next cell denoting the hour that the appliance has
been programmed to operate (the ON symbol indicates
the cells that the appliance has been programmed to
operate). Thus you can adjust the temperature for each
hour of the appliance's operation. If you do not want to
make any changes to the temperature settings, you can
leave the weekly setting mode by holding the PROG
button pressed. The changes to the weekly programme
have been made.
•
"Eco Smart" mode
By pressing the ECO/SMART button you can choose
between three modes: ECO, EC1 and EC2. In Eco Smart
mode the electric heater elaborates its own algorithm for
operation so as to ensure energy saving, and therefore, to
reduce your electricity bill and at the same time to keep
the comfort in your home while it is being used.
Instructions for using the built-in wireless communication module (Wi-Fi)
EN
27