Optional Accessories - Makita AN902 Manual De Instrucciones

Contact actuation
Pull the trigger first and then place the contact element
against the workpiece. (Fig. 13)
Jammed nailer (Fig. 14)
CAUTION:
• Always disconnect the air hose and remove the nails
from the magazine before cleaning a jam.
When the nailer becomes jammed, do as follows:
Open the magazine cap and remove the nail coil. Insert a
small rod or the like into the ejection port and tap it with a
hammer to drive out the nail jamming from the ejection
port. Reset the nail coil and close the magazine cap.
Nails
Handle nail coils and their box carefully. If the nail coils
have been handled roughly, they may be out of shape or
their connector breaks, causing poor nail feed. (Fig. 15)
Avoid storing nails in a very humid or hot place or place
exposed to direct sunlight. (Fig. 16)
MAINTENANCE
CAUTION:
• Always disconnect the air hose from the tool before
attempting to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Maintenance of nailer
Always check the tool for its overall condition and loose
screws before operation. Tighten as required. (Fig. 17)
With tool disconnected, make daily inspection to assure
free movement of the contact element and trigger. Do not
use tool if the contact element or trigger sticks or binds.
(Fig. 18)
When the tool is not to be used for an extended period of
time, lubricate the tool using pneumatic tool oil and store
the tool in a safe place. Avoid exposure to direct sunlight
and/or humid or hot environment. (Fig. 19 & 20)
Maintenance of compressor, air set and air hose
After operation, always drain the compressor tank and
the air filter. If moisture is allowed to enter the tool, it may
result in poor performance and possible tool failure.
(Fig. 21 & 22)
Check regularly to see if there is sufficient pneumatic oil
in the oiler of the air set. Failure to maintain sufficient
lubrication will cause O-rings to wear quickly. (Fig. 23)
Keep the air hose away from heat (over 60°C, over
140°F), away from chemicals (thinner, strong acids or
alkalis). Also, route the hose away from obstacles which
it may become dangerously caught on during operation.
Hoses must also be directed away from sharp edges and
areas which may lead to damage or abrasion to the
hose. (Fig. 24)
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Nails
• Air hoses
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN ISO 11148-13:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 2.5 dB (A)
Wear ear protection
Vibration
The vibration total value determined according to EN ISO
11148-13:
Vibration emission (a
Uncertainty (K): 1.26 m/s
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
ENG905-1
): 98.3 dB (A)
pA
): 98.9 dB (A)
WA
ENG904-2
2
): 2.52 m/s
h
2
ENG901-1
15