Additional Safety Warnings - Makita PW5001C Manual De Instrucciones

the locating diameter of the flange. Accessories that
do not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
7. Do not use a damaged accessory. Before each use
inspect the accessory such as backing pad for cracks,
tear or excess wear. If power tool or accessory is
dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an acces-
sory, position yourself and bystanders away from the
plane of the rotating accessory and run the power tool
at maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
8. Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping flying debris generated by various operations.
The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged expo-
sure to high intensity noise may cause hearing loss.
9. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear per-
sonal protective equipment. Fragments of workpiece
or of a broken accessory may fly away and cause injury
beyond immediate area of operation.
10. Position the cord clear of the spinning acces-
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled into
the spinning accessory.
11. Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the
power tool out of your control.
12. Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
13. Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
14. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool to
be forced in the direction opposite of the accessory's rotation
at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction
of the wheel's movement at the point of pinching. Abrasive
wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or kick-
back forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite
to the wheel's movement at the point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and snagging
the accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades create
frequent kickback and loss of control.
Safety Warnings Specific for Stone Polishing
Operations:
a) Do not use excessively oversized abrasive
disc. Follow manufacturers recommendations,
when selecting abrasive disc. Larger abrasive
disc extending beyond the pad presents a lacer-
ation hazard and may cause snagging, tearing of
the disc or kickback.

Additional safety warnings:

15. Ground Fault Circuit Interrupter (GFCI) pro-
tection should be provided on the circuit(s) or
outlet(s) to be used for the tool. Receptacles
are available having built-in GFCI protection
and may be used for this measure of safety.
16. For additional protection against electric
shock, be sure to WEAR RUBBER GLOVES
AND RUBBER BOOTS during operation.
17. When using the water feed, be careful not to let
water get into the motor. If water runs into the
motor, an electric shock hazard may result.
18. PROPER GROUNDING. This tool should be
grounding while in use to protect the operator
from electric shock.
19. EXTENSION CORDS. Use only three-wire
extension cords which have three-prong
grounding-type plugs and three-pole recepta-
cles which accept the tool's plug. Replace or
repair damaged or worn cord immediately.
20. Make sure the abrasive disc is not contacting
the workpiece before the switch is turned on.
21. Do not leave the tool running. Operate the tool
only when hand-held.
22. Check that the workpiece is properly supported.
23. Pay attention that the wheel continues to
rotate after the tool is switched off.
24. Do not use the tool on any materials contain-
ing asbestos.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may
cause serious personal injury.
4 ENGLISH