Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Electronic pulse mode, self drilling
screw mode (2) and drill mode
Electronic clutch mode
(reverse rotation)
Elapsed time after switching on
The tool may not return to the initial status from the
striking operation.
When the bit or socket is removed from the screw or
bolt while the switch is being pulled, the tool may
continue the striking operation.
To return to the initial status, turn off the switch and
then start the next operation.
Motor rotation speed does not decrease even when
the remaining battery power becomes low.
Since this tool adopts the constant-speed control, the
rotation speed is almost unchanged even when the
remaining amount of the battery becomes low. This
allows users to operate the tool efficiently until GCe
battery runs down. However, it is difficult to know the
remaining battery power from the rotation speed
and the tool may stop suddenly during work.
The tool stops automatically when the electronic
clutch is actuated.
Quiet screw tightening can be performed without
clutch sound generated by the mechanical type.
The tool stops automatically when the clutch is
actuated. If you continue to use the tool, turn off the
switch once and turn it on again. When the tool does
not operate even without load, the remaining amount
of the battery is low. In this case, recharge the battery
immediately.
3. Check the rotational direction
The bit rotates clockwise (viewed from the rear side)
by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the
bit counterclockwise. (See Fig. 7) (The
marks are provided on the body.)
CAUTION
The push button can not be switched while the tool is
turning. To switch the push button, stop the tool,
then set the push button.
4. Switch operation
When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
The rotational speed can be controlled by varying
the amount that the trigger switch is pulled. Speed is
low when the trigger switch is pulled slightly and
increases as the trigger switch is pulled more.
5. Using the light
Pull the trigger switch to light up the light. The light
keeps on lighting while the trigger switch is being
pulled. The light goes out after releasing the trigger
switch. (Fig. 8)
Self drilling screw
mode (1)
Bolt mode
L
Electronic clutch mode
(regular rotation)
R
R
L
and
CAUTION
Do not expose directly your eyes to the light by
looking into the light.
If your eyes are continuously exposed to the light,
your eyes will be hurt.
6. Tightening and loosening screws
Install the bit that matches the screw, line up the bit in
the grooves of the head of the screw, then tighten it.
Push the tool just enough to keep the bit fitting the
head of the screw.
CAUTION
Applying the tool for too long tightens the screw too
much and can break it.
Tightening a screw with the tool at an angle to that
screw can damage the head of the screw and the
proper force will not be transmitted to the screw.
Tighten with this tool lined up straight with the screw.
Use the bit that fits the cross recess on the screw head.
Make sure to use an appropriate bit especially when
tightening self drilling screws since using an
inappropriate bit can topple the screws.
ABOUT BATTERY BCL1030A
Remaining battery indication
[Meaning of indication]
Indicator lamp
: Light OFF
: Lights or blinks in green
Status
Output stop
Remaining
0% – 10% 10% – 30% 30% – 50% 50% – 75% 75% – 100%
battery level
Remaining
battery
indication
• In charging:
The number of blinking indicator lamps
increases to indicate the charge level
of the battery.
• Pause:
The indicator lamps blink continuously
to indicate the remaining charge of
the battery.
•
Power tool
When the switch of the cordless power
in use:
tool is turned on, the indicator lamps
light to indicate the remaining charge
of the battery. About 3 seconds after
the switch is released, the indicator
lamps begin to blink (status in pause).
•
Auto-stop
Only the top indicator lamp blinks rapidly
activated:
(every 0.5 second) and stops output.
Auto-stop function
To prevent operation with a weakened power tool, this
battery has an auto- stop function to stop output when
the remaining battery level becomes 30% or less.
When the auto-stop function is activated, only the top
indicator lamp blinks rapidly. Then please charge the
battery immediately.
Indication of abnormality
When the remaining battery indicator lamps of the battery
blink rapidly (every 0.5 second), the battery may have a
fault. Please bring it back to your dealer or the Hitachi
Authorized Service Center.
English
Output possible
10
Tabla de contenido
