Protecting The Environment - DeWalt D26411 Manual De Instrucciones

• To prevent igniting the surface, do not keep the tool
directed at one spot too long.
• Avoid collecting paint on the scraper accessory, as it may
ignite. If necessary, carefully remove paint debris from the
scraper accessory using a knife.
1. Attach the appropriate accessory.
2. Turn the air temperature adjustment knob/ LCD air
temperature indicator and adjuster
3. Turn the tool on by selecting the desired air flow.
4. Direct the hot air onto the paint to be removed.
Best results will be achieved if the heat gun is moved
slowly, but CONSTANTLY, from side to side to evenly
distribute heat. DO NOT LINGER OR PAUSE IN ONE SPOT.
5. When the paint softens, scrape the paint away using a
hand scraper.
REMEMBER: Splinters and small particles of stripped paint
can be ignited and blown through holes and cracks in the
surface being stripped.
Stationary Use (Fig. A)
This tool can also be used in stationary mode.
1. Fold down the kickstand
2. Set the tool onto a level, stable workbench. Ensure the
tool will not tip over.
3. Secure the power cord to prevent entanglement or
pulling the tool off the workbench.
4. Turn the tool on by selecting the desired air flow.
Constant Heat Control
(overload protection)
When the tool is overloaded, this feature protects the
heating element from damage without stopping the tool
and/or without a cool down period
1. When the temperature gets too hot, the heating
element switches itself off. The motor will continue to
run and produce cold air.
2. When the temperature has cooled sufficiently (taking
only a few seconds) the heating element will switch
on automatically.
Tool Ring (Fig. A)

WARNING: ALWAYS turn heat gun off, disconnect
from the power source and let the tool cool down for
at least 30 minutes before moving or storing it.
For easy storage, the tool can hang from the tool ring
The heat gun should be stored indoors.
Cool Down Period
The nozzle and accessory becomes very hot during use.
Turn heat gun off, disconnect from the power source and
let the tool cool down for at least 30 minutes before moving
or storing it.
NoTE: To reduce the cooling time, switch the tool on at
the lowest air temperature setting and let it run for a few
minutes before turning the heat gun off.
4 to high.
3 as shown in Figure A.
6 .
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D WALT factory service center
e
or a D WALT authorized service center. Always use
e
identical replacement parts.

Protecting the Environment

Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions.
ENglIsh
WALT
e
21