Dip Switch Settings - JB Systems Light MICRO LED MANAGER Manual De Instrucciones

ENGLISH
FUNCTIONS
1. INTERNAL MICRO: used for sound activated chases.
2. DMX INPUT: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller or from another Micro Led Manager when used in master/slave mode.
3. DMX OUTPUT: 3pin female XLR-connector used to connect the Micro Led Manager with the next DMX
appliance in the chain or with another Micro Led Manager when used in master/slave mode. The Micro
LED Manager can also be used as controller for other LED projectors like for example "LED PAR56/64"
4. POWER ON LED: used to check if the Micro LED Manager is connected to the mains.
5. DIP SWITCHES: when used in DMX mode (DIP10 = OFF) you can set the DMX-starting address of the
unit. When used in stand-alone mode (master, DIP10 = ON), you can use the DIP-switches to set
different pre-programmed options.
6. AUTO DMX ADDRESS BUTTON: see further to learn how to set the DMX address easily.
7. OUTPUT TERMINALS: used to connect different 24Vdc common anode LED projectors. (max. load:
50W) You can connect any 4pole electrical wire to connect the LED-projectors to this output. However to
make life easier for you we suggest using the special CCM-50 cable (role = 50m). The wires in this cable
correspond to the colors of the LEDs .
8. ANALOG SWITCH INPUT: used to connect any external analog switch. This external switch can be
used to switch the general output of the Micro LED Manager on/off. (external blackout)  See further for
more information on how to connect the analog switch.
9. WALL DIMMER INPUT: used to connect our LED WALL DIMMER, a small LED controller that fits in any
standard "electrical wall box".  See further for more information on how to connect the LED WALL
DIMMER.
10. MAINS INPUT: with IEC socket, connect the supplied mains cable here.
11. STATUS LED: shows the status of the unit, should blink when DMX is detected.

DIP SWITCH SETTINGS

Dip switch 10:
Dipswitch setting Function
DIP10 = OFF  DMX / Slave operation
You can use the automatic DMX addressing feature or traditional DIP-switches.
In the chapter DMX-addressing, we explain how DMX-addressing can be done.
DIP10 = ON  Master operation (stand-alone)
Use the dipswitches 1~9 to set the mode, speed, patterns, fixed color color...etc functions.
Below each of these functions is explained in detail.
Dip switches 1&2: Mode (Sound/auto/fade/fixed color):
Dipswitch setting MODE
SOUND: internal microphone triggers the selected patterns.
AUTO: the selected pattern runs automatically at the desired speed.
JB SYSTEMS®
OPERATION MANUAL
3/54 MICRO LED MANAGER
ENGLISH
FADE: the colors of the selected pattern fade smoothly at the desired speed.
FIXED COLOR: use DIP-switches 6, 7, 8 & 9 to select the desired colors.
Dip switches 3,4 & 5:Speed (from fast to slow):
Dipswitch setting Auto/Fade Mode
Speed 1
Speed 2
Speed 3
Speed 4
Speed 5
Speed 6
Speed 7
Speed 8
DIP switches 6,7 ,8 & 9: Chase & Color:
Dipswitch setting SOUND & AUTO MODE
Standard chase
Bright chase
Mood chase
Spectrum random chase
Spectrum sequence chase
Dynamic chase
Chase Red – Cyan
Chase Green – Purple
Chase Blue – Red
Chase Yellow – Blue
Chase Red – Green
Chase Yellow – Green
Chase Cyan – Orange
Chase Green - Light purple
Chase Red – Yellow
Chase Gold Yellow - Blue
JB SYSTEMS®
OPERATION MANUAL
Fast
Slow
FIXED COLOR MODE
White
Red
Orange
Amber
Yellow
Light Yellow
Apple Green
Light Green
Green
Cyan
Blue
Deep Blue
Purple
Light Purple
Magenta
Pink
4/54 MICRO LED MANAGER