Key Functions - Steinberg Systems SBS-BW Serie Manual De Instrucciones

KEY FUNCTIONS

WARNING SIGNALS AND STATE
Battery Level (lb)
If your balance shows LB and produces a beep at the same time , the battery reaches
for about 1 hour of work. Connect the scale on the sector. The LB display and the
beep tone stop, and the AC LED will turn on. To fully charge the battery, let the scale-
load for 4h.
X DISPLAY SECURITY
Status "NO"
When the scale displays "NO", the circuit does not work.
The balance must be repaired.
BUTTONS AND OPTIONS
With the switch I / O on the back of the device, you can turn the scale on. A self-test
starts. It begins with a test of the screen and the diodes. The screen should display
0.0.0.0.0.0. and all the LEDs should light. Then the information on the current calib-
ration values is displayed (from the factory: 0150.05: 0150 stands for 150kg and 0.5
for the measurement interval), as well as the programmation of the calculator (Uer_3,
EN
2 for ver3,2) and the state of the battery (eg. dC_U5, 0 for 5.0 V) After the test, the
scale is ready to use when it displays 0.00. Press the button I / O again to turn off the
scale.
For the SBS-BW-3T/1KG scale model, the connection between the scale head and
the scale platform is wireless. The communication between the head and the platform
is being established right after switching on the scale head and the scale platform. The
scale platform is equipped with three control lights:
AC – means that the storage battery of the platform is charging (AC power is con-
nected)
Low Voltage – means that the platform storage battery needs to be charged
SIGNAL – after proper wireless connection between the scale head and the scale
platform this light will be blinking.
If the scale display will show „Err24", it means that there is wireless connection error
(the platform is off or the platform storage battery needs to be charged).
TARE (ZERO)
Before weighing, make sure that ZERO and STABLE indicators are on the left and the
desired unit is on the right. This means the optimum state of operation of the device.
If the ZERO indicator is not turned on or the display is not showing zero after taking
off the load from the scale, then the key [ZERO/TARE] must be pressed. The scale will
confirm the tare showing 0.00. The weight window will display the net weight value.
10
ERROR MESSAGES
"Ad_Err" The weight cannot be measured by the sensor. Necessary
repairs.
"Lo_bat" Charge the battery
--- --- OL Overload. Too much weight on the scale
Seterra The internals data are not correct. Necessary repairs.
DO NOT PRESS THE BUTTON (ZERO / TARE)
until the weight is not stable, (ie until the LED STABLE is not lit) to avoid measure-
ment errors.
TARE (ZERO)
To tare, place an empty container on the platform when the STABLE LED is lit. Then
press (ZERO / TARE) for the scale to ignore the weight of the container.
CAUTION
After the tare, the maximum capacity is reduced by the weight of the container!
Eg container b = 90kg, normal max weigh s= 150kg Max. capacity Left: s-b = 60kg.
Immediately remove the weight in case of overload! OL ---- (----)
HOLD (HOLD)
If the weight is superior to 0.05 kg in weighing mode, the save mode can be activa-
ted by pressing the HOLD button. At the same time, the HOLD LED lights up as a
confirmation. Press the HOLD key again to exit the hold mode and to return to the
weighing mode.
UNIT CHANGE (UNIT / KG / LB, LB / KG)
With the (UNIT) key, you can change units between lb and kg. Press the button
(UNIT) to choose the right unit.
PACK FUNCTION
There are 2 selections under PACK function: IN & OUT. The default setting is "NO",
which means ALARM and PACK functions in non-work status; When it is under IN,
it will alert between UPPER and LOWER limit; When it is under OUT setting, it
will alarm that the weight exceeds the upper limit or below LOWER limit. It shows
HHHHHH when exceeding UPPER limit and LLLLLL when below LOWER limit.
11
EN