Standard Accessories; Prior To Operation - HIKOKI FSV 10SA Instrucciones De Manejo

h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
SPECIFICATIONS
Voltage (by areas) *
Power Input
No-load speed
Sanding pad size
Sanding paper size
Weight (without cord) **
* Be sure to check the nameplate on product as it is subject to change by areas.
** According to EPTA-Procedure 01/2014.

STANDARD ACCESSORIES

○ Sanding paper ..............................................................6
(Grain: #60, #100, #150 ......................................2 each)
○ Dust bag .......................................................................1
○ Punch plate ..................................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
1. Sanding paper
Grain: #60, #100, #150 (3 types)
2. Sanding paper (Magic type)
Grain: #60, #100, #150 (3 types)
3. Pad (Magic type)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Finish polishing of woodwork surfaces
○ Sanding surfaces of woodwork or sheet metal prior to
painting, etc.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF positon. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach
of children and infirm persons.
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
180W*
10000 min
92 mm × 184 mm
93 mm × 228 mm
1.4 kg
4. Installing the sanding paper
Align the hole in the base with the sanding paper holes.
Place the sanding paper over the base. Next line up
both ends of the sanding paper with the base width-
wise, and fold the sanding paper (Fig. 1).
Align the fold with the edge of the base, and grip one
side with the paper holder (Fig. 2).
Now grip the opposite side of the sanding paper with
the paper holder.
CAUTION
The sanding paper must be precisely installed on the
pad, ensuring that there is ample tension (leaving no
slack). Loosely installed sanding paper could result
in unevenly sanded surfaces and/or damage to the
sanding paper itself.
5. Attaching and Removing the Dust Bag
(1) Attaching the Dust Bag
As shown in Fig. 3, hold the dust gate and push it in the
direction of Arrow A to attach it to the dust outlet.
(2) Removing the Dust Bag
As shown in Fig. 3, hold the dust gate and pull it in the
direction of Arrow B to remove it from the dust outlet.
CAUTION
Prior to the sanding operation, make sure the material
of surface you are going to sand.
If the surface under sanding operation is expected to
generate harmful / toxic dusts such as lead painted
surface, make sure the dust bag or appropriate dust
extraction system is connected with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts
generated in sanding operation, the dust can endanger
the health of yourself and bystanders.
PRACTICAL OPERATING PROCEDURES
CAUTION
Never apply water or grinding fluid when sanding. This
could result in electrical shock.
1. Switching the sander ON and OFF
The power can be turned on by setting the lever to ON
(1) and turned off by setting the lever to OFF (0).
English
–1
7