Additional Safety Warnings; Standard Accessories - HIKOKI SV 12V Instrucciones De Manejo

h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Prior to the sanding operation, make sure the material
you are going to sand.
If generation of harmful/ toxic dusts such as lead paint,
woods and metals is expected under the sanding
operation, make sure the dust bag or appropriate dust
extraction system is connected with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts generated
in sanding operation, the dust can endanger the health
of yourself and bystanders.
5. Practical operating procedures
○ Never apply water or grinding fluid when sanding. This
could result in electrical shock.
○ Never turn the power switch ON when the sander is
contacting the surface to be sanded. This is necessary
to preclude damage to the material. The same applies
when switching the power OFF.
○ DO NOT apply excessive pressure to the sander while
sanding. Excessive-pressure may cause overload of the
motor, reduced service life of the sanding paper, and
lowered sanding or polishing efficiency.
6. Attaching a Sponge Pad (Velcro type) or a Stick-on pad
(optional accessories)
Replace the pad only. Use the other parts without
removing them.
7. Attaching Velcro Type Sanding Paper or Stick-on Type
sanding Paper (optional accessories)
Match the sanding paper's hole with the pad's hole and
strongly push the sanding paper with the palm of your
hand to fasten it securely in place.
8. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
SV12V / SV12SD : Orbital Sander
To reduce the risk of injury, user must read
instruction manual.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V Rated voltage
P Power input
n
No-load speed
0
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
○ Sanding paper ............................................................. 1
○ Dust bag ...................................................................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Finish polishing of woodwork surfaces
○ Sanding surfaces of woodwork or sheet metal prior to
painting, etc.
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input
No-load speed
Diam. of Orbit
Sanding pad size
Sanding paper size
Weight (without cord)**
* Be sure to check the nameplate on product as it is subject
to change by areas.
** According to EPTA-Procedure 01/2014
3
English
SV12V SV12SD
(110 V, 120 V, 220 V, 230 V,
240 V)
300 W
4000 – 10000 min 10000 min
-1
2.4 mm
114 mm × 228 mm
114 mm × 280 mm
2.9 kg
-1