DeWalt DCPS620 Manual De Instrucciones página 15

Pruning With the Pole Saw (Fig. A, O, Q)

WARNING: Let the tool work at its own pace.
Do not overload.

WARNING: When pruning trees: guard against
kickback which can result in severe injury or death.
See guard Against Kickback, to avoid the risk of
kickback. Do not overreach. Make sure your footing
is firm. Keep feet apart. Divide your weight evenly on
both feet.
1. Use both hands to grip pole saw as shown in Figure O.
Use a firm grip. Thumbs and fingers must wrap around
pole saw handle and pole. Keep fingers away from
sawdust exhaust chute
2. Never operate while in a tree, in any awkward position
or on a ladder or other unstable surface. You may lose
control of pole saw causing severe injury.
3. Follow directions below to trim a tee.
a. Make sure pole saw is running at full speed before
making a cut. When starting a cut, place moving saw
chain 14 against limb. Hold pole saw firmly in place
to avoid possible bouncing or skating (sideways
movement) of pole saw.
b. Guide pole saw using light pressure. Make first cut
6" (152 mm) from tree trunk on underside of limb.
Use top of guide bar
through diameter of limb. Then make the finish cut
from the top. If you try to cut off thick branches
from the bottom, the branch may close in and pinch
the saw chain in the cut. If you try to cut off thick
branches from the top, without a shallow undercut,
the branch may splinter. Do not force pole saw.
The motor will overload and can burn out. It will
do the job better and safer at the rate for which it
was intended.
c. Remove pole saw from cut while it is running at full
speed. Stop pole saw by releasing trigger switch
Make sure saw chain has stopped before setting pole
saw down.
Fig. Q
Saw Chain Sharpness

CAUTION: Sharp chain. Always wear protective
gloves when handling the chain. The chain is sharp
and can cut you when it is not running.
IMPORTANT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail while cutting.
To get the best possible performance from your chain saw it
is important to keep the teeth of the saw chain sharp. Chain
26 shown in Figure Q.
13 to make this cut. Cut 1/3
sharpening services are available from your nearest D
service center.
nOTE: Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should
be used. It is recommended that a saw chain be sharpened
no more than four times.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Regular maintenance ensures a long effective life for the
tool. After every 10 minutes of use be sure to remove the
battery (be aware the chain and bar can be hot!) check
the bar and chain for correct tension and lubricate per
Adjusting Chain Tension and Chain Oiling.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
4 .
this product.
Replacement chain and bar are available from your
nearest D WALT service center.
e
• DCPS620 requires replacement chain service part
number DWO1DT608. Replacement 8" (203 mm) bar,
service part number DWZCSB8.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
26
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D
Always use identical replacement parts.
WALT, have not been tested with this
e
WALT Industrial
e
WALT authorized service center.
e
English
WALT
e
WALT
e
WALT factory
e
13