Safety Regulations; Layout And Items Supplied - EINHELL TE-TS 2231 UD Manual De Instrucciones

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.

2. Layout and items supplied

2.1 Layout (Fig. 1-4)
2.1.1. Bench-type circular saw
1. Saw table
2. Splitter
3. Cover for extractor connection
4. Saw blade guard
5. Saw blade
6. Stop rail
7. Universal stop
8. Guide rail for universal stop (front)
9. Guide rail for universal stop (left)
10. Locking grip - angle setting
11. Locking grip - position
12. Scale for saw blade angle
13. Crank handle for cutting height
14. Fixing handle for saw blade angle
15. Table insert
16a. Leg (front right/back left)
16b. Leg (front left/back right)
17. Rubber foot (type A)
18. Cross strut
19. Chassis
20. Longitudinal strut
21. Rubber foot (type B)
22a. Lug (left, length extension table)
Anl_TE_TS_2231_U_2831_UD_SPK7.indb 28 Anl_TE_TS_2231_U_2831_UD_SPK7.indb 28
GB
22b. Lug (right, length extension table)
23. Transport handle
24. Folding length extension table
25. Strut for length extension table
26. Locking grip for length extension table
27. Holder (for push stick, push block)
28. Push block handle
29. Push stick
30. Key for changing the saw blade
31. Open-ended wrench for blade change
32. Self-locking nut size M8
33. Self-locking nut size M6
34. Nut M6
35. Washer, large
36. Washer, medium
37. Washer, small
38. Extraction hose
39. Spring washer, small
40. Hex screw (M4 x 10)
41. Hex screw (M6 x 16)
42. Extractor connection (housing)
43. Screw (for table insert)
44. Switch/plug block
45. On/Off switch
46. Scale (cutting height)
47. Scale (parallel stop)
48. Lug (foot)
49. Allen screw (for length extension table)
2.1.2 Slide
(special accessories – not supplied):
100. Slide plate with scale
101. Stop rail
102. Guide rail
103. Angle (rear)
104. Clamping lever for angle setting
105. Angle (front)
106. Strut (rear)
107. Strut (front)
108. Hex screw M10 x 65
109. Washer 8mm
110. Spacer ring (plastic)
111. Allen screw (long)
112. Allen screw (short)
113. Button
114. Spring washer
115. Profi le
116. Nut size M8, self-locking
117. Washer 6 mm (large)
118. Hex screw (M8 x 16)
119. Hex screw (M6 x 16)
120. Nut size M6, self-locking
121. Nut size M8, self-locking (plastic lock)
122. Washer 10 mm
123. Washer 8 mm, small
- 28 -
23.04.14 08:39 23.04.14 08:39