Starting The Engine; Vehicle Operation; Loading Platform - Active 1310 Manual De Instrucciones

WARNING: read the safety regulations carefully. If
you have never used this vehicle, familiarise yourself with
all the controls.
- Check the vehicle carefully for oil leaks before use. Make
sure that there are no loosened screws, damaged
components or oil/fuel leaks.
- Make sure that controls can work properly.
- Check engine oil (see the attached handbook).
ENGINE START-UP fig. 1
1- Check that clutch lever (1) is in "NEUTRAL" position
(A), i.e. disengaged (see fig. 5).
2- Check that gear lever (5) is in "NEUTRAL" position (N),
i.e. disengaged (see fig. 1).
3- Move the air control device to the (B) position fig. 1/A
4- Open the fuel valve, position (C) fig. 1/A
5- Move throttle control (2) to the intermediate position.
6- Turn the stop switch "ON" (1)
7- Grasp the starter grip (7) and pull slowly until resistance
is felt. Then pull cord rapidly and start engine. Repeat if
1- Select an appropriate speed, by means of gear lever
(5) fig.1.
WARNING: do not force the gear lever: to select a gear,
engage and then disengage clutch lever (1) fig. 1, up until
the gear can be engaged easily.
Make sure that the gear has been engaged properly
2- Lower clutch lever (1) fig. 1 slowly, and make sure it is
close to the knob; then the vehicle will start moving.
3- To stop the vehicle, release clutch lever (1) fig.1
quickly
WARNING: on uneven grounds engage the first gear
(slow). Do not change gear while you are driving your ve-
hicle.
Do not change speed or make "U" turns.
4- To adjust speed, move throttle control (2) fig. 1 slowly.
EXTENDABLE PLATFORM fig. 2
- The loading platform of this vehicle is provided with ex-
tendable flaps, in order to adjust the dumper size, ac-
cording to your requirements.
- To change the dumper size, simply loosen knobs (1)
and pull out the flap as required
DUMPER
- Dumper is available on demand, to transport liquids.
WARNING: stop the vehicle slowly, to prevent load
overturning.
- Make sure that the platform has been loaded properly.
Do not overload. Overloading or using the vehicle on ex

STARTING THE ENGINE

necessary.
8- After starting the engine, move the air control device to
position (A) fig. 1/A
9- When the engine is warm, do not shut-off the air
(starter).
ENGINE STOP fig. 1
1- Release clutch lever (1) in order to disengage the
gearbox.
2- Move gear lever (5) to "N" (neutral position).
3- Move throttle control (2) to minimum position, and wait
for a few seconds, to let the engine cool down.
4- To automatically stop the engine, turn the engine
switch to (0)"OFF" position.
5- Close fuel valve (D) fig. 1/A.

VEHICLE OPERATION

CHANGING DIRECTION fig. 1
- Move the left-hand or right-hand lever of the side
clutches (3) in order to drive your vehicle in the desired
direction.
RIGHT-HAND LEVER: the vehicle moves to the right
LEFT-HAND LEVER: the vehicle moves to the left
If both levers are pulled simultaneously the vehicle stops
immediately.
If the lever is pulled only in part, the steering radius is
wide. Pull it completely to reduce the radius
"RIGHT-HAND" and "LEFT-HAND" refer to the
operator, while he is driving the vehicle, i.e.
grasping the control handle.
REVERSE GEAR: before moving in reverse gear, make
sure that the area behind you is free of any obtacles and
that you can drive in full safety

LOADING PLATFORM

cessive slopes may damage the vehicle and overturn the
load.
MANUAL UNLOADING fig. 3
- Lifting: press release lever (A) close to the handle (7)
and lift the dumper.
- Lowering: grasp handle (7), lower the dumper and make
sure it is locked by the clamping device.
- Lifting: press release lever (A) close to the handle (7)
and lift the dumper.
- Lowering: grasp handle (7), lower the dumper and make
sure it is locked by the clamping device.
29
ENGLISH ENGLISH
ENGLISH ENGLISH ENGLISH
MANUAL UNLOADING fig. 3
GB