Sears 61011 Manual De Uso página 34

Ocultar thumbs Ver también para 61011:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Installation
Instructions
<con nuod)
1. Install
a manual
gas line shut-offvalve
in the gas
line in an easily accessed
location
outside
of the
range. Make
sure everyone
operating
the range
lmows where
and how to shut off the gas supply
to
the range.
2. Install
male 1/2" flare union
adapter
to the 1/2"
NPT
internal
thread
elbow at inlet of pressure
regulator.
On models
equipped
with standard
twin
burners,
install
the male pipe thread
end of the 1/2"
flare union
adapter
to the 1/2" NPT
internal
thread
at inlet of pressure
regulator.
Use a back-up
wrench
on the regulator
fitting
to avoid damage.
When
installing
the range from the front, remove
the 90 ° elbow for easier installation.
3, Install male
!/2" or 314" flare union
adapter
to the
NPT
internal
thread
of the manual
shut-off
valve,
takSng care to back up the shut-offvatve
to keep it
from turning.
4. Connect
flexible metal appliance
connector
to the
adapter
on the range. Position
range to permit
connection
at the shut-offvalve.
5. When
all connections
have been made,
make sure
all range controls
are in the OFF
position
and turn
on the main gas supply valve. Use a liquid leak
detector
at all joints and connections
to check for
leaks in the system.
!
CAUTION:
DO NOT
USE A FLAME
TO
[
l
CHECK
FOR GAS LEAKS.
i
When
using
test pressures
greater
than
t/2 psig to
pressure
test the gas supply
system
of the residence,
disconnect
the range and individual
shut-offvalve
from the gas supply
piping.
When
using test pressures
of 1/2 psig or less to test the gas supply
system,
simply
isolate the range from the gas supply
system by closing
the individual
shut-off
valve.
STEP 3
Electrical
Connections
(on some
models)
HectricaI
Requirements
t20-volt,
60 Hertz,
properly
grounded
branch
circuit
protected
by a 15-amp
or 20-amp
circuit
breaker
or
time delay fuse.
Extension Cord Cautions
Because
of potential
safety hazards
associated
with
certain
conditions,
we strongly
recommend
against
the
use of an extension
cord° However,
if you still elect to
use an extension
cord, it is absolutely
necessary
that it
be a UL-listed,
3-wire
grounding-type
appliance
extension
cord and that
the current
carrying
rating
of
tile cord in amperes
be equivalent
to, or greater
than,
the branch
circuit
rating.
Groundlng--IMPORTANT
(Please
read carefully)
FOR
PERSONAL
SAFETY,
THIS
APPLIANCE
MUST
BE PROPERLY
GROUNDED°
The power cord of this
appliance
is equipped
with a three-prong
(groundin_
plug
which
mates with a
standard
three-prong
grounding
wall
receptacle
to minimize
the possibility
of'
electric
shock hazard
from
this appliance.
PREFERRED
METHOD
before use
The customer
should
have the wall receptacle
and
circuit
checked
by a qualified
electrician
to make sure
the receptacle
is properly
grounded.
Where
a standard
two-prong
wall receptacle
is
encountered,
it is the personal
responsibility
and
obligation
of the customer
to have it replaced
with a
properly
grounded
three-prong
wall receptacle.
DO
NOT, UNDER
ANY CIRCUMSTANCES,
CUT
OR REMOVE
THE THIRD
(GROUND)
PRONG
FROM
THE
POWER
CORD.
34
Tabla de contenido
loading

Tabla de contenido