General Power Tool Safety Warnings; Additional Safety Rules - Makita 7104L Manual De Instrucciones

Escopleadora de cadena
Ocultar thumbs Ver también para 7104L:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 25
ENGLISH (Original instructions)
1.
Wing bolt
2.
Stopper pole
3.
Stopper
4.
Lock-off button
5.
Switch trigger
6.
Adjusting screw
7.
Chain bar
8.
Chain cover
9.
Hex bolt
10. Arrow
11. Sprocket
12. Lever (A)
13. Vise lever
SPECIFICATIONS
Capacities
Width of applicable workpiece
Dimensions (L × W × H)
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting mortise in wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool's plug.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.

ADDITIONAL SAFETY RULES

1. Use this tool only to cut holes in wood.
Explanation of general view
14. Rear vise
15. Setting handle
16. Front vise
17. Indicator plate
18. Indication plate
19. Cutting line (A)
20. Cutting line (B)
21. Hook
22. Hex bolts
23. Gauge plate
24. Travel distance (D)
25. Lever (B)
26. Lever (C)
Model
Max. hole length
(Longitudinal)
Max. hole depth
Chain speed
Net weight
Safety class
ENE062-1
GEA010-1
ENB093-1
2. This tool is for cutting holes in flat-surfaced wood.
Never use it for cutting holes in a log.
3. Wear ear protectors.
ENF001-1
4. Handle the cutter chain carefully; it is very sharp.
5. Place the workpiece on wood blocks or short
beams to prevent the cutter chain from hitting the
ground, floor, etc., causing damage to the cutter
chain at the time of hole breakthrough.
6. Check the cutter chain carefully for cracks or
damage before operation. Replace cracked or
damaged cutter chain immediately.
7. Secure the tool to the workpiece firmly.
8. Inspect for and remove nails or foreign matter
from the workpiece before operation.
9. Do not operate the tool with the safety cover open.
10. Do not wear gloves during operation.
11. Keep hands away from moving parts.
12. Remove the tool from the workpiece after
operation to keep it from falling off and possibly
causing injury.
13. Don't abuse cord. Never yank cord to disconnect
it from the receptacle. Keep cord away from heat,
oil, water and sharp edges.
14. PROPER GROUNDING. This tool should be
grounding while in use to protect the operator
from electric shock.
27. Adjusting hex bolt for No. 1 set
position
28. Adjusting hex bolt for No. 2 set
position
29. Original position
30. No.1 set position
31. No.2 set position
32. Ruler
33. Front vise
34. Limit mark
35. Brush holder cap
36. Screwdriver
7104L
130 mm
155 mm
80 mm – 308 mm
300 m/min
512 mm × 298 mm × 513 mm
17.3 kg
Class I
5
Tabla de contenido
loading

Tabla de contenido