Functional Description - Makita AN935H Manual De Instrucciones

Selecting air hose
CAUTION:
Low air output of the compressor,
or a long or smaller diameter air hose in relation
to the nailing frequency may cause a decrease in
the driving capability of the tool.
► Fig.3
Use a high pressure resistant air hose.
Use an air hose as large and as short as possible to
assure continuous, efficient nailing operation.
Lubrication
► Fig.4: 1. Pneumatic tool oil
Oil the tool with pneumatic tool oil by placing two or
three drops into the air fitting. This should be done
before and after use.
For proper lubrication, the tool must be fired a couple of
times after pneumatic tool oil is introduced.
FUNCTIONAL
DESCRIPTION
CAUTION:
Before adjusting or checking func-
tion on the tool, always lock the trigger by turning
the trigger lock lever to the lock position
disconnect the air hose from the tool.
Adjusting depth of nailing
This toll has the adjuster of the nailing depth. To mod-
ulate the nailing depth, turn the adjuster to the proper
depth.
► Fig.5: 1. Adjuster
The adjustable range is 8.5 mm (11/32"). (One full turn
allows 1.25 mm (1/16") adjustment.)
► Fig.6: 1. Too deep 2. Flush 3. Too shallow
Hook
CAUTION:
Always disconnect the hose when
hanging the tool using the hook.
CAUTION:
Never hook the tool at high loca-
tion or on potentially unstable surface.
CAUTION:
Do not hang the hook from the
waist belt. If the nailer accidentally drops, it may
result in misfiring and personal injuries.
The hook is useful for hanging up the tool temporarily.
The hook can be turned while pushing the bottom to the
desired angle.
► Fig.7: 1. Hook
Furthermore, this hook can be installed on either side
of the tool.
To change the installation position, remove the bolt with
a hex wrench. Install the hook on another side and then
secure it firmly with the bolt.
► Fig.8: 1. Hook 2. Bolt
Nose adapter
To prevent the surface of workpiece from being
scratched or damaged, use the nose adapter.
To detach the nose adapter from its housing base, pull
the nose adapter in the direction of the arrow.
► Fig.9: 1. Nose adapter
To attach the nose adapter to the contact element,
press it onto the contact element until the recessed
parts in four places inside the nose adapter fit in four
protrusions of the contact element.
► Fig.10: 1. Nose adapter 2. Contact element
Air duster
CAUTION:
air duster to someone. Also, keep your hands and
foot away from the ejection port. If the air duster
button is accidentally pushed, it may cause a per-
sonal injury.
CAUTION:
before using the air duster. Blown dust or objects
may hit someone.
CAUTION:
air hose while pushing the air duster button.
The air supplied to the tool can also be used as an air
, and
duster. You can clean the work area by pressing the
button on the grip end.
► Fig.11: 1. Button
NOTICE:
of the tool will temporarily decline. Wait until the air
pressure recovers in this case.
NOTICE:
duster immediately after the oil was applied. The oil
may be sprayed with the air.
ASSEMBLY
CAUTION:
the tool, always lock the trigger by turning the
trigger lock lever to the lock position
disconnect the air hose from the tool.
Loading nailer
CAUTION:
linked sheet.
1. Disconnect the air hose.
2. Depress the latch lever and open the door and
magazine cap.
► Fig.12: 1. Latch lever 2. Door 3. Magazine cap
► Fig.13
10 ENGLISH
3. Protrusion 4. Recessed part
Do not aim the ejection port of the
Always check your surroundings
Do not connect or disconnect the
After using the air duster, the driving force
Perform a test blow if you use the air
Before carrying out any work on
Do not use deformed nails or
, and