En Original Operating Instructions; Declaration Of Conformity; Specified Conditions Of Use; General Safety Information - Metabo KPA 12 400 Manual De Instrucciones

en ENGLISH
Original operating instructions

1. Declaration of Conformity

We hereby declare under our sole responsibility
that these cordless cartridge guns, identified by
type and serial number *1), meet all relevant
requirements of directives *2) and standards *3).
Technical documents for *4) - see page 3.

2. Specified Conditions of Use

The device is designed to extrude sealant or
adhesive from cartridges or plastic bags.
It is not designed for foodstuffs or for medical/
veterinary purposes. It should not be used with
pressurized cartridges. The gun should also not be
used as a lifting/spreading tool.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Information

For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference. Pass on your electrical tool only
together with these documents.

4. Special Safety Instructions

A slightly acidic, flammable fluid may leak
from defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
Protect battery packs from water and
moisture!
Do not use faulty or deformed battery packs!
Do not expose battery packs to fire!
8
Do not open battery packs!
If the machine is defective, remove the battery pack
from the machine.
Do not touch or short circuit battery pack contacts!
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Make sure that the tool is switched off before fitting
the battery pack.
Do not use frozen or set adhesive or sealant.
Do not overload the motor! If the motor is
overloaded, switch off the device and remove the
battery pack. Determine the cause of the problem
and resolve it.
Refer to the instructions for assembling the device.
Ensure that the front cap, tube and threaded ring
are correctly fitted and securely fastened.
Always wear eye protection.
Danger of crushing! Do not take hold of the toothed
rod (6)! Ensure that nothing is caught by the toothed
rod.
Follow national requirements for the materials you
want to work with.
Refer to the glue or adhesive manufacturers'
instructions and also the safety data sheet for the
consumable material.
Adhesives and sealants can be dangerous. For this
reason, you should always carefully read any
instructions on the container or other information
provided by the manufacturer about the material to
be used. Do not use materials without knowing what
risks they entail.
Do not use any solvent, acidic or other abrasive
cleaning agents.
Store the device and its components in a safe place
(e.g. Ensure that the dismantled tube (3) is not
allowed to roll away).
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
5. Overview
See page 2.
1 Front cap
2 Nozzle (for plastic bag) *
3 Tube
4 Half shell (for insertion of cartridges) *