Technical Data; Before Starting The Appliance - EINHELL DHG 200 Manual De Instrucciones Original

Anleitung_DHG_200_SPK7__ 20.04.16 13:43 Seite 16
GB
temperature has been reached the appliance is
automatically switched off, and if the temperature
should drop again, it is automatically switched back
on.
A photo cell permanently monitors the combustion
process and turns the appliance on or off if there are
irregularities. If overheating occurs, the appliance will
also switch off.
If this is the case, please contact customer service.
The electrical components are protected by a
miniature fuse (fusible insert). If there is a fault in the
miniature fuse, please contact customer service.

6. Technical data

Power supply:
Heat output (Hi):
Heat settings:
Fuel: Low-sulphur heating-oil or diesel
Pump pressure:
Fuel consumption:
Tank capacity:
Power rating:
Air flow rate:
Maximum air temperature:
Appliance dimensions:
Appliance weight:

7. Before starting the appliance

Before you connect the appliance to the power
n
supply make sure that the data on the rating plate
are identical to the mains data.
Always place the portable device on firm,
n
horizontal ground.
The device must always be in an upright position.
n
Take care that the minimum separating distance
n
between the appliance and other objects is 2.5m
at the front, 1.25m at the rear and the side.
The appliance must only be used in well-
n
ventilated rooms or outdoors. The required size of
the air intake opening in the room is 0.02m
kW of heat output. For a heat output of 20kW the
openings would need to be 0.4m
addition, be sure to open windows and doors
outwards.
16
7.1 Assembly (Fig. 2).
n
8. Operation
8.1 Refuelling
Guidelines and recommendations:
n
n
n
n
230 V ~ 50Hz / 1.5A
20 kW
n
1
n
0.28 bar
2.0 l/h
n
19 l
1. Remove the tank cover (Fig. 1/Item 8).
170 W
2. Fill the tank up slowly with low-sulphur heating oil
400 m /h
3
393 °C
3. Replace the tank cover.
76 x 30.5 x 38 cm
13 kg
8.2 Switching ON (Fig. 3)
Guidelines and recommendations:
n
n
n
per
2
in total size. In
2
1. Connect the power plug with an extension cable.
2. Set the desired temperature (between +5°C and
Screw the carrying handle (Fig. 2/Item 3) onto the
upper half of the housing (Fig. 2/Item 2)
The required low-sulphur heating oil or diesel
must be stored in a container clearly marked with
"Low-sulphur heating oil" or "Diesel".
Please observe the applicable regulations valid
for your country when storing low-sulphur heating
oil and diesel.
Never use "bio-diesel".
We recommend for you to use winter diesel if
temperatures are below 5°C to avoid problems
with fuel suction.
Low-sulphur heating oil and diesel will age.
Therefore they should be used up within 6
months.
Only refuel outdoors and when the appliance has
cooled down.
Follow the safety information (section 1).
or diesel until the indicator (Fig.1/Item 7) indicates
"F". The tank volume is 19 Litres maximum.
The hot air generator can be plugged into any
shockproof socket with 230V alternating current
for which there is a fuse with a 10A circuit breaker.
It is advisable to connect the appliance only to an
electricity supply protected by a residual-current
operated protective device (RCD) with a release
current of 30 mA max.
Only use power cables which are not damaged.
The power cable length is restricted (50m max.).
The power cable must have a cross section of at
least 3x1.0mm.
We recommend to start up the device outdoors
for the first time and let it run for around 10
minutes to burn off any oil residue on the sheet
metal parts which may have built up during
production.
+45°C) by adjusting the thermostat knob (Item