DeWalt DWE7470 Manual De Instrucciones página 51

Be sure to place the blade guard assembly and standard throat plate back in position
and check adjustments when the dado cuts are complete. Reinstall blade guard
assembly, anti-kickback assembly and riving knife.
Dust Collection (Fig. 42)
Your table saw is equipped with a dust shroud
and dust collection port. For best results,
connect a vacuum to the port at the rear of the
saw.
After extended use, the saw's dust collection
system may become clogged. To clear the dust
collection system:
1. Unplug the saw.
2. Turn the saw on its side, so the bottom,
open part of the unit is accessible.
3. Open the dust access door A5) shown in
Figure 42 by removing the screws (V V).
Clean out the excess dust, and re-secure
the access door with the screws.
Storage (Fig. 4, 43)
1. Place blade wrenches (R). into storage slot.
2. Place push stick (U) into storage bracket as shown.
3. Slide rip fence (E) into storage bracket
4. Mitre gauge (B) is stored in slot on fence storage bracket.
5. Wrap power cord onto cord wrap (O) and secure in place.
FIG. 43
U
R
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect tool from
power source before installing and removing accessories, before making any
adjustments or removing/installing attachments or accessories. An accidental start-up
can cause injury.
Your D WALT power tool has been designed to operate over a long period of time with a
E
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care
and regular cleaning.
Cleaning
WARNING: When cleaning, use only mild soap and a damp cloth on plastic parts. Many
household cleaners contain chemicals which could seriously damage plastic. Also, do not use
FIG. 42
A5
V V
B
E
gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products which may
seriously damage plastic parts. Never let any liquid get inside the tool; never immerse any part
of the tool into a liquid.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including
brush inspection and replacement) should be performed by authorized service centers or other
qualified service personnel, always using identical replacement parts.
Lubrication
1. All motor bearings are permanently lubricated at the factory and no additional lubrication
is needed.
2. The height adjustment gear may require periodic cleaning and lubrication. If you have
difficulty raising or lowering the blade, contact a D
Accessories
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT, recommended accessories should be used with this product.
E
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center.
Protecting the Environment
Separate collection. This product must not be disposed of with normal household
waste.
Should you find one day that your D WALT product s replacement, or if it is of no further use
E
to you, do not dispose of it with household waste.
Separate collection of used products and packaging allows materials to be recycled
and used again. Re-use of recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical products from the household,
at municipal waste sites or by the retailer when you purchase a new product.
D WALT provides a facility for the collection and recycling of D
E
have reached the end of their working life. To take advantage of this service please return your
product to any authorized service center that will collect them on our behalf.
You can check the location of your nearest authorized service center by contacting your
local D WALT office. Alternatively, a service center listing is included in the packaging of this
E
product.
SPECIFICATIONS
Voltage:
Frequency:
Current Rating:
RPM without load:
49
WALT authorized service center.
E
WALT, have not been tested
E
WALT products once they
E
DWE7470-B3
120 V ~
50-60 Hz
1800 W
5 000/min