Roland PK-9 Manual Del Usuario página 112

MIDI Pedalboard PK-9
MIDI Implementation
General Purpose (Controller number 18)
Status 2nd byte
BnH 12H
n= MIDI channel number:
vv= Control value:
General Purpose (Controller number 19)
Status 2nd byte
BnH 13H
n= MIDI channel number:
vv= Control value:
Hold 1 (Controller number 64)
Status 2nd byte
BnH 40H
n= MIDI channel number:
vv= Control value:
Portamento (Controller number 65)
Status 2nd byte
BnH 41H
n= MIDI channel number:
vv= Control value:
Filter Resonance (Timbre/Harmonic Intensity) (Controller
number 71)
Status 2nd byte
BnH 47H
n= MIDI channel number:
vv= Resonance value
(relative change):
Cutoff (Controller number 74)
Status 2nd byte
BnH 4AH
n= MIDI channel number:
vv= Cutoff value
(relative change):
Pitch Bend Change
Status 2nd byte
EnH llH
n= MIDI channel number:
mm, ll= Pitch Bend value:
Channel Mode Messages
MONO (Controller number 126)
Status 2nd byte
BnH 7EH
n= MIDI channel number:
mm= mono number:
POLY (Controller number 127)
Status 2nd byte
BnH 7FH
n= MIDI channel number:
System Realtime Messages
Active Sensing
Status
FEH
This message is transmitted at intervals of approximately
250 ms.
System Exclusive messages
Data Set 1 (DT1) is the only System Exclusive messages
transmitted by the PK-9.
112
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127) 0~63= OFF,
64~127= ON
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (-64~0~+63)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH(-64~0~+63)
3rd byte
mmH
0H~FH (Ch.1~16)
00 00H~40 00H~7F 7FH
(–8192~0~+8191)
3rd byte
mmH
0H~FH (Ch.1~16)
00H~10H (0~16)
3rd byte
00H
0H~FH (Ch.1~16)
Data set 1 DT1 (12H)
Status Data byte
F0H 41H, 10H, 00H, 02h, 12H, aaH, bbH,
ccH, ddH, ... eeH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
10H Device ID
00H Model ID (MSB)
02H Model ID (LSB)
12H Command ID (DT1)
aaH Address MSB: upper byte of the
starting address of the data to be
sent (12H).
bbH Address: middle byte of the starting
address of the data to be sent
(Parameters Group address 00H –
03H).
ccH Address LSB: lower byte of the
starting address of the data to be
sent (00H)
ddH Data: the actual data to be sent.
Multiple bytes of data are
transmitted in order starting from
the address.
: :
eeH Data
sum Checksum
F7H EOX (End Of Exclusive)
Address of Parameters Group
Address(H) Parameter group
13 00 00 Retrigger, Velocity, Touch, Portamento Time,
Octaver Value, Pedal Assign, Transpose, Octave,
MIDI Channel
Status
F7H