Starting And Stopping - Ryobi RY42WB Manual Del Operador

ETHANOL-BLENDED FUELS
NOTICE:
Do not use E15 or E85 fuel in this product. It is a viola-
tion of federal law and will damage the unit and void
your warranty. Only use unleaded gasoline containing
up to 10% ethanol.
FUELING AND REFUELING THE BLOWER
WARNING:
Gasoline and its vapors are highly flammable and ex-
plosive. To prevent serious personal injury and property
damage, handle it with care. Keep away from ignition
sources and open flames, handle outdoors only, do not
smoke and wipe up spills immediately.
FUEL MIXTURE
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded
gasoline and 2-cycle engine lubricant in a clean container
approved for gasoline. DO NOT mix quantities larger than
usable in a 30-day period.
Recommended fuel: This engine is certified to operate on
unleaded gasoline intended for automotive use.
NOTE: We recommend you use Ethanol Shield 2-cycle lubri-
cant or an equivalent high-quality synthetic 2-cycle lubricant
in this product. Mix at 2.6 oz. per gallon (US).
Do not use automotive lubricant or 2-cycle outboard
lubricant.
HIGH QUALITY 2-CYCLE ENGINE LUBRICANT
GASOLINE
1 gallon (US)
1 liter
FILLING TANK
 Clean surface around fuel cap to prevent contamination.
 Loosen the fuel cap slowly by turning counterclockwise.
Rest the cap on a clean surface.
 Carefully pour fuel mixture into the tank. Avoid spillage.
 Prior to replacing the fuel cap, clean and inspect the
gasket.
 Immediately replace fuel cap and hand tighten by turning
it clockwise. Wipe up any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new
engine after first use.
OPERATION
Always shut off engine before fueling. Never remove fuel
cap or add fuel to a machine with a running or hot engine.
Make sure the unit is sitting on a flat, level surface and
only add fuel outdoors. If the engine is hot, let the unit cool
for at least five minutes before adding fuel. After fueling,
immediately replace fuel cap and tighten securely. Move
at least 30 ft. from refueling site before starting engine. Do
not smoke and stay away from open flames and sparks!
Failure to follow these instructions could result in a fire
and cause serious personal injury.

STARTING AND STOPPING

See Figures 4 - 6.
Blower should be on a flat, bare surface for starting.
 Slowly press the primer bulb 10 times.
 Set the choke lever to the START position.
 Pull starter grip and rope sharply until engine attempts to
 Set the choke lever to the RUN position.
 Pull the starter grip and rope until the engine runs. Do not
 Allow the engine to run for 20 seconds before using the
TO STOP THE ENGINE:
LUBRICANT
 To stop the engine, press and hold the on/stop switch in
2.6 oz.
20 cc (20 ml)
HOT RESTART OF THE ENGINE:
 Set the choke lever to the RUN position.
 Pull the starter grip and rope until the engine runs.
IF ASSISTANCE IS REQUIRED STARTING THIS PRODUCT:
Do not return this product to the retail store where it was
purchased. Please call our Customer Service Department
for any issues you may have.
For Help Call: 1-800-860-4050.
8 — English
WARNING:
NOTE: After the 10th press, fuel should be visible in the
primer bulb. If it is not, continue to press the primer until
you see fuel in the bulb.
run. Do not pull the starter grip and rope more than five
(5) times.
pull the starter grip and rope more than six (6) times.
NOTE: If the engine does not start, return to the START
position and repeat the steps that follow.
blower.
the stop ( ) position.