Operating Elements And Connections; Safety Notes; Setting The Spotlight Into Operation - IMG STAGELINE PARC-64/CTW Manual De Instrucciones

All operating elements and connections de -
GB
scribed can be found on the page 2.
1 Operating Elements
and Connections
1 Locking screws for the mounting brackets
2 Mounting brackets / stand
3 Display
4 XLR chassis plug DMX INPUT: DMX signal
input for connecting a light controller or the DMX
signal output of another spotlight
5 Clip to secure the barn doors (optional)
6 XLR jack DMX OUTPUT: DMX signal output for
connecting the DMX input of another DMX-con-
trolled unit
7 Buttons to select the operating mode and to
change settings via the menu
8 Mains cable for connection to a socket (230 V~/
50 Hz)

2 Safety Notes

The spotlight corresponds to all relevant directives
of the EU and is therefore marked with
WARNING The spotlight uses dangerous mains
voltage. Leave servicing to skilled
personnel and do not insert anything
into the air vents; inexpert handling
may result in electric shock.
G
The spotlight is suitable for indoor use only. Pro-
tect it against dripping water and splash water,
high air humidity and heat (admissible ambient
temperature range: 0 – 40 °C).
G
Do not operate the spotlight or immediately dis-
connect the mains plug from the socket
1. if the spotlight or the mains cable is visibly
damaged,
2. if a defect might have occurred after a unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the spotlight must be repaired by
skilled personnel.
G
A damaged mains cable must be replaced by
skilled personnel only.
G
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the plug.
G
No guarantee claims for the spotlight and no lia-
bility for any resulting personal damage or mate-
rial damage will be accepted if the spotlight is
used for other purposes than originally intended, if
it is not safely installed or not correctly connected
or operated, or if it is not repaired in an expert way.
8
G
Important for U. K. Customers!
The wires in this mains lead are coloured in ac -
cord ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of
this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
1. The wire which is coloured green and yellow
must be connected to the terminal in the plug
which is marked with the letter E or by the earth
symbol , or coloured green or green and yel-
low.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the spotlight is to be put out of operation
definitively, take it to a local recycling plant
.
for a disposal which is not harmful to the
environment.
3 Applications
This LED spotlight is used for illumination, e. g. on
stage, in discotheques and function rooms. The light
source is a white high-power COB LED (COB = chip-
on-board technology): Many individual LEDs are
mounted close together on a chip, thus providing a
uniform light distribution. Half of the individual LEDs
mounted on the chip are designed for warm white,
and half of the LEDs are designed for cool white.
Change the brightness ratio between cool white and
warm white to set the colour temperature of the light
beam to a value between 2700 K and 5600 K.
The spotlight is designed for control via a DMX
light controller (4 DMX control channels), but it can
also be operated independently without a controller.

4 Setting the Spotlight into Operation

4.1 Installation
G
Always position the spotlight in such a way to
ensure sufficient air circulation during operation.
Never cover the air vents of the housing.
G
Always keep a minimum distance of 50 cm to the
illuminated object.