Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Definitions:
Safety
Guidelines
The definitions below describe the level of severity for each signal word. Please read
the manual and pay attention to these symbols.
i_,DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious
injury.
AWARNING:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious
injury.
_&CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate
injury.
CAUTION:
Used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property
damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT
TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT
(1-800-433-9258)
Important
Safety
Instructions
A
ARNING:
Read all instructions
before operating product. Failure to follow all
instructions fisted below may result in electric shock, fire and/or serious injury.
READ
ALL INSTRUCTIONS
Double
Insulation
Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one double thickness of insulation between you and the tool's electrical sys-
tem. Tools built with this insulation system are not intended to be grounded. As a result,
your tool is equipped with a two prong plug which permits you to use extension cords
without concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when oper-
ating this tool. The insulation system is for added protection against injury resulting from a
possible electrical insulation failure within the tool.
ACAUTION:
WHEN SERVICING
USE ONLY IDENTICAL
REPLACEMENT
PARTS.
Repair or replace damaged cords.
Polarized
Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the
risk of electric shock. When provided, this plug will fit in the polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Safety
Instructions
For All Tools
•
KEEP GUARD IN PLACE and in working order.
•
REMOVE ADJUSTING
KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from spindle before turning tool on. Tools,
scrap pieces, and other debris can be thrown at high speed, causing injury.
•
KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
•
DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT.
The use of power
tools in damp or wet locations or in rain can cause shock or electrocution.
Keep your
work area well-lit to avoid tripping or placing arms, hands, and fingers in danger.
•
KEEP CHILDRENAWAY.
All visitors shouldbe keptata
safe distance from workarea.
Your shop is a potentially dangerous environment.
•
MAKE WORKSHOP
CHILDPROOF
with padlocks, master switches, or by removing
starter keys. The unauthorized start-up of a machine by a child or visitor may result in
injury.
•
DON'T FORCE TOOL. It will do the job better and be safer at the rate for which it was
designed.
•
USE RIGHT TOOL. Don't force tool or attachment
to do a job for which it was not
designed. Using the incorrect tool or attachment may result in personal injury.
•
WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or
other jewelry to get caught in moving parts. Non-slip footwear is recommended.
Wear
protective hair covering to contain long hair. Air vents may cover moving parts and
should also be avoided.
• ALWAYS
USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI $12.6 (S3.19) hearing protection
•
NIOSH/OSHA/MSHA
respiratory protection
•
SECURE
THE WORKPIECE.
Use clamps or a vise to hold the workpiece on the
table and against the fence or when your hand will be dangerously close to the blade
(within 6"). It is safer than using your hand and it frees both hands to operate tooL
•
DON'T OVERREACH.
Keep proper footing and balance at all times. Loss of balance
may cause personal injury.
•
MAINTAIN
TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance.
Follow instructions
for lubricating
and changing
accessories.
Poorly
maintained tools and machines can further damage the tool or machine and/or cause
injury.
•
TURN THE MACHINE
"OFF';
AND DISCONNECT
THE MACHINE
FROM
THE
POWER
SOURCE
before installing or removing accessories,
before adjusting or
changing set-up& when making repairs or changing locations.
An accidental start-up
can cause injury. Do not touch the plug's metal prongs when unplugging or plugging in
the cord.
•
REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure that the switch is
in the "OFF" position before plugging in the power cord.
•
USE PROPER
EXTENSION
CORD. Make sure your extension
cord is in good
condition.
If your product is equipped
with a cordset, use only 3-wire extension
cords that have 3-prong grounding-type
plugs and 3-pole receptacles that accept
the tool's plug.
When using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating.
The following table shows
the correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Minimum
Gauge for Cord Sets
Volts
120V
240V
Ampere Rating
More
Not more
Than
Than
O-
6
6-
10
10 -
12
12 -
16
Total Length of Cord in Feet
0-25
26-50
51-100
101-150
0-50
51-100
101-200
201-300
AWG
18
16
16
14
18
16
14
12
16
16
14
12
14
12
Not Recommended
•
CHECK for DAMAGED
PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate properly
and perform its intended function--check
for alignment of moving parts, binding of
Capítulos
Tabla de contenido
