Making The Connections - Monacor PA-302 Manual De Instrucciones

5 Making the Connections

All connections should only be made by quali-
fied personnel and in any case with the amplifier
switched off!
1) Connect the supplied microphone to the jack
MIC (2) .
2) Connect the speakers (min . impedance 4 Ω) for
PA applications to the terminal strips LSP 1 and
LSP 2 (13) . These speakers are also used as micro-
phones for the reply during intercom operation .
Hint: For better handling when fastening the ca-
bles with screws, the connection terminals can be
removed from their plug-in connections .
3) For the reproduction of the reply during intercom
operation, a speaker has been integrated into the
amplifier . It can be supported or replaced by an
additional speaker (min . impedance 4 Ω) . Connect
the speaker to the terminal strip EXT . LSP (12)
according to fig . 4 . Only remove the jumper (a)
for switching off the integrated speaker .
EXT. LSP
a
Additional speaker for the intercom operation
➃
4) For PA music applications of the amplifier, con-
nect an audio unit with line output (e . g . MP3 / CD
player, radio set, etc .) to the jack AUX (14) .
5) Finally connect the operating voltage of 12 V (⎓)
or 24 V (⎓) to the terminal strip 12 – 24 V ⎓ (10) .
The amplifier automatically switches to 12 V or
24 V operation .
6 Operation
1) To prevent possible switching noise, prior to
switching-on turn the controls MIC /AUX (4) and
GAIN (5) counter-clockwise to minimum . Switch
on the unit with the switch POWER (9) . The
POWER LED (8) lights up .
2) Use the switches LSP 1 and LSP 2 (7) to switch on
the speakers via which the announcement or the
PA applications are to be made .
3) Adjust the desired mode of operation with the
rotary switch (6):
AUX = the unit connected to the jack AUX (14) is
selected for PA music applications
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®
INTERCOM = intercom operation via the con-
nected microphone and the speakers con-
nected to the terminals LSP 1 and 2 (13)
FOG = activation of fog horn via the talk button
(15) of the microphone or via the button SIREN /
FOG (3) on the amplifier
FOG AUTO = the fog horn automatically emits
a short sound at an interval of one minute
approx .
SIREN = activation of siren via the talk button of
the microphone or via the button SIREN / FOG
on the amplifier
SIREN AUTO = permanent siren sound
Note: the fog horn and the siren always sound at
maximum volume (not adjustable) .
4) Adjust the volume for microphone announce-
ments and for PA music applications with the
control MIC /AUX (4) . For an announcement, keep
the talk button (15) on the microphone pressed .
5) During intercom operation, the speakers con-
nected to the terminals LSP 1 and LSP 2 (13) serve
as microphones for a reply . For the reproduction
of the reply via the integrated speaker and / or
via the speaker connected to the terminal EXT .
LSP (12), do not keep the talk button (15) on the
microphone pressed . Adjust the volume for the
reply with the control GAIN (5) .
If the intercom operation is not used, turn the
control GAIN counter-clockwise fully to minimum .
7 Specifications
Rated power: . . . . . . . . . . . 14 W
Music power: . . . . . . . . . . . 20 W
Inputs
1 × MIC: . . . . . . . . . . . . . 3 mV
1 × AUX: . . . . . . . . . . . . . 50 mV
Outputs
3 × speakers: . . . . . . . . . . 4 – 16 Ω
Frequency range: . . . . . . . . 20 – 20 000 Hz
S / N ratio: . . . . . . . . . . . . . . 65 dB
THD: . . . . . . . . . . . . . . . . . . < 0 .5 %
Power supply: . . . . . . . . . . . 12 – 15 V (⎓) / 2 A
Ambient temperature: . . . . 0 – 40 °C
Dimensions (W × H × D): . . 175 × 60 × 170 mm
Weight: . . . . . . . . . . . . . . . 1 .5 kg
Subject to technical modification .
or 24 V (⎓) / 1 A
7