Maintenance And Replaceable Parts; General Maintenance; Battery Replacement - Urrea UD88 Manual De Usuario Y Garantía

E N G L I S H
Temperature
Switches
Ignition System
Coils
Condensers
Connectors
Contact Set (points)
MAF Sensors
Magnetic Pickup
MAP/BP Sensors
O² Sensors
Starting System
Batteries
Connectors
Interlocks
Solenoids
Starters
APPLICATIONS GUIDE
Ignition / Engine
Coils •
Computer Temp
Sensors
Condensers
•
(Capacitors)
Conectors •
Contact set • • •
Distributor cap
Engine Speed
Feedback
• •
Carburetors
Fuel injectors
• • •
(electronic)
Hall-Effect Sensors •
Idle Air Motors • • • • •
Ignition Modules •
MAF Sensor
Magnetic Pickups • •
MAP & BP Sensors •
O2 Sensors •
Throttle Position
•
Sensors
Starting system
Battery •
Connectors
Interlocks (neutral
•
safety switch)
Solenoids •
Starters •
Cooling system
Connectors •
Fan Motor •
Radiator
Relays •
Temperature
Sensors
86
• • •
• •
• •
• • •
• •
• •
• • •
• •
• •
• •
• •
•
• • •
• • •
• •
• • •
• •
• • • • •
• • •
•
•
• • •
• •
• • • • • • •
• • •
• •
• • •
• • • • • •
• •
• • •
• •
• •
• • • •
• •
• • • • •
• • • •
• • • •
• •
• •
• • •
• • •
Temperature
Switches
Charging System
Alternators •
Computarized
•
Regulated
Connectors
Diodes (AC Ripple)
Diode Rectifier
Regulators • • •
Body Electric
Compressor Clutch
Lighting Circuits
Relay and Motor
Diodes
Transmissions
* Used with a DC current clamp
7. MAINTENANCE AND REPLACEABLE
PARTS

General Maintenance

WARNING: REPAIRS OR SERVICING NOT COVERED IN THIS
MANUAL SHOULD ONLY BE PERFORMED BY QUALIFIED
PERSONNEL. TO AVOID ELECTRICAL SHOCK, DO NOT
SERVICE UNLESS YOU ARE QUALIFIED TO DO SO.
Periodically wipe the case with a damp cloth and
•
detergent; do not use abrasives or solvents. Water, dirt
• •
or contamination in the A or mA μA input terminals
• •
may harm this Meter. Calibrate this Meter once a year
•
•
to maintain its performance specifications.
•

Battery Replacement

•
The Meter uses a 9V battery (NEDA 1604 or IEC 6F22).
• •
To replace the battery, remove the two screws of the
• battery compartment from the back of the Meter and
•
lift off the cover of the compartment. Replace the
battery. Reattach the battery compartment to the
•
back of the Meter and reinstall the screws.
•
Fuse (s) Test
•
To test the internal fuses of this Meter:
• •
1. Set the rotary switch to the "
•
2. To test the F2 (15A, 600V) insert a test lead into the
•
or VΩRPM CAP input terminal and touch the probe to
• •
the A input terminal.
•
The display should read about 0.000V. If the display
•
reads "OFL" (overflow), replace the fuse and test
•
again. If the display reads any other value, have this
Meter serviced.
• • • • • •
• • • • •
• • •
• • •
• •
•
• •
• • • •
•
• •
" position.
• •
• •
•
•
•
•