Electrical Installation - JB Systems Light MLS-20 Manual De Instrucciones

ENGLISH
Tape mounted on the bottom
Mounting with smallscrews:
This takes a little more time but the mounting surface doesn't have to
be so smooth, you can even fix the LED strip on a surface covered
with carpet.
 Remove the PCB from the U-shaped plastic rail just by sliding it to
one side.
Important: do NOT touch the electrical contacts on the bottom
of the PCB, electrostatic discharges can destroy the LEDs!!!
Now you can easily drill small holes in the plastic rail. (see picture)
 Fix the plastic rail on the surface using adapted small screws.
 Slide the PCB back in place (don't forget to first put the supplied
small connection cable to the output connector on the bottom)
Hint: You can install the LED STRIP(s) also behind translucent plastic panels to create color changing walls
and ceilings or in a bar you can install the strips under a translucent shelf to lighten bottles and drinking
glasses from the bottom.

ELECTRICAL INSTALLATION

The electrical installation should be carried out by qualified personal only, according to the
regulations for electrical and mechanical safety in your country.
VERY IMPORTANT: Check the user manual of the LED Manager for the maximum allowed power on
its outputs! Do not exceed this maximum allowed power! To know the total power consumption of all
LED products in a chain you simply have to add up the power consumption of all units in the chain.
Check the chapter "specifications" at the end of this manual to see the power consumption of the
different LED STRIPS!
!! This MLS-20 + MLS-50 MINI LED STRIP can only be used together with the JB SYSTEMS
!!! DON'T CONNECT DIRECTLY TO 230Vac or any ordinary 24Vdc power supply !!!
 After installing the units just daisy chain the in/output cables of all LED STRIP units up to the maximum
allowed load.
 After checking that the maximum allowed power is not exceeded, you can connect the chain to one of the
outputs of the LED Manager.
 To connect the first LED STRIP in the chain to the LED MANAGER, please do the following:
 Cut off one end of the connection cable that was supplied with the LED STRIP
 Use a simple 4-pin contact terminal to connect the open ends of the cable to the special cable
supplied with the LED MANAGER: the corresponding colors should be connected to each other.
Attention: you must take the two white colored wires of the small connection cable together.
JB SYSTEMS
®
OPERATION MANUAL
Tape mounted on the side
®
LED MANAGER !!
3/25 MLS-20 + MLS-50 MINI LED STRIP
ENGLISH
Example: You have to install 33x MLS-50 and 6x MLS-20  33x 3,4W + 6x 1,7W = 122,4 Watt. This chain
can be connected to one of the LED Manager outputs since it does not exceed the allowed 150W.
maximum output for Mini LED Manager is 100W! )
OPERATING INSTRUCTIONS
Since the MINI LED STRIPS are controlled by the LED Manager, we strongly advice to read the operation
instructions in the LED Manager user manual.
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the LED Manager and unplug the mains cable.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an enclosure is visibly damaged due to cracks or deep scratches, it must be replaced.
 The cables must be in impeccable condition and should be replaced immediately when even a small
problem is detected.
 The cleaning of the plastic enclosure must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty
surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
SPECIFICATIONS
Connections: Special flat cables
Operation voltage : 24Vdc common anode
Power consumption: MLS-20 (20cm) = 1,7 Watt
MLS-50 (50cm) = 3,0 Watt
Size/Weight: MLS-20 (20cm) = 43 g
MLS-50 (50cm) = 93 g
JB SYSTEMS
®
OPERATION MANUAL
4/25 MLS-20 + MLS-50 MINI LED STRIP
(Attention: