Special Safety Instructions - Metabo MAG 32 Instrucciones De Manejo

en ENGLISH
condition that may affect the tool's operation. If
damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained
tools.
5.8 Use only accessories that are
recommended by the manufacturer for your
model. Accessories that may be suitable for one
tool may become hazardous when used on another
tool.
6 Service
6.1 Tool service must be performed only by
qualified repair personnel. Service or
maintenance performed by unqualified personnel
could result in a risk of injury.
6.2 When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance
instructions may create a risk of electric shock or
injury.

3. Special Safety Instructions

Always use securing strap. Mounting can release.
For your own protection and for the
protection of your power tool, pay atten-
tion to all parts of the text that are marked
with this symbol!
For work carried out on angled and vertical
surfaces and overhead, the magnetic drill
stand must be secured with the securing strap
supplied to prevent it from falling if the power supply
is interrupted.
When the magnet is switched off, or if the power
supply is interrupted, the magnet loses it holding
power. The machine executes a dangerous
swinging movement.
Always wear a hard hat when working overhead.
Always wear protective goggles, gloves, and suit-
able shoes when working.
Ensure there is no damage to the mains connection
cables, switch and anti-kink device.
Arc welding on the workpiece on which the machine
is used is prohibited.
If a change in normal operation is detected (e.g.
motor starts when magnet (switch (19)) is switched
on: do not use the machine but have it repaired.
Further faults can occur.
The magnet produces magnetic and electromag-
netic fields that can have a negative effect on
medical implants.
The surface for the electromagnet must be clean
and flat.
The magnet holding power depends on material
thickness and condition.
Paint, zinc and oxide layers reduce the magnet
holding power.
Do not expose the machine to rain and do not use in
wet or potentially explosive rooms.
Disconnect the mains plug from the plug socket
before performing any adjustments or maintenance
6
on the machine. Caution! When you unplug the
mains plug, the magnet loses its holding power.
If (after use) the magnetic drill stand is placed on a
material with low heat-dissipation characteristics for
a long period (e.g. plastic), the magnet must not be
switched on because this could lead to overheating
of the magnetic coils.
Follow the instructions for lubrication and tool
replacement.
Keep the handles dry, clean and free of oil and
grease.
Caution! The use of other tools and accessories can
result in a risk of injury.
Use the handle (4) on the magnetic drill stand when
transporting the machine.
Always wear a safety harness when working
on scaffolds.
Wear ear protectors.
Wear protective goggles.
Danger - electrical voltage.
Danger - magnetic field.
Persons with pacemakers prohibited.
Additional Warnings:
Some dust created by power
WARNING
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
Symbols on the tool:
V .............. volts
A .............. amperes
W ............. watt
Hz ............ hertz
.../min....... revolutions per minute
~ .............. alternating current
n ............. no load speed
0
California Prop 65 08_2018