Gima HOSPI PLUS Manual De Istrucciones página 16

The HOSPI PLUS SUCTION ASPIRATOR is intended for use in the electromagnetic environment specified below. The
customers or the user of the HOSPI PLUS SUCTION ASPIRATOR should assure that it's used in such an environment.
Immunity Test Level indicated by
Conducted Immunity
EN 61000-4-6
supporting devices)
Radiated Immunity
EN 61000-4-3
supporting devices)
Note 1: At 80 MHz and 800 MHz the interval with the highest frequency is applied
Note 2: These guide lines may not be applicable in all situations. The electro-magnetic propagation is influenced by the absorption
and by reflection from buildings, objects and people.
a) The field intensity for fixed transmitters such as the base stations for radiotelephones (mobile and cordless) and terrestrial
mobile radio, amateur radio devices, radio AM and FM transmitters and TV transmitters can not be theoretically and accurately
foreseen. To establish an electro-magnetic environment generated by fixed RF transmitters, an electro-magnetic study of the site
should be considered. If the field intensity measured in the place where the device will be used surpasses the above mentioned
applicable level of conformity, the normal functioning of the device should be monitored. If abnormal performance arises,
additional measures such as changing the device's direction or positioning may be necessary.
b) The field intensity on an interval frequency of 150 kHz to 80 MHz should be less than 3 V/m.
Recommended separation distance between portable and mobile radio-communication devices and the monitor
the user of the HOSPI PLUS SUCTION ASPIRATOR device can help prevent electromagnetic interference by maintaining a minimum distance
The surgical aspirator is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or
between portable and mobile RF communication equipment (transmitters) and the HOSPI PLUS SUCTION ASPIRATOR device, as recommended
below, according to the maximum output power of the communications equipment.
Maximum nominal
output power of
150 kHz to 80 MHz
the
d = [3.5 / V
Transmitter W
0,01
0,1
1
10
100
For transmitters with a maximum nominal output power not shown above, the recommended separation distance in metres (m)
can be calculated using the equation applicable to the transmitter frequency, where P is the maximum nominal output power of
the transmitter in Watt (W) depending on the transmitter's manufacturer.
Note 1: At 80 MHz and 800 MHz the interval with the highest frequency is applied
Note 2: These guide lines may not be applicable in all situations. The electro-magnetic propagation is influenced by the absorption
and by the reflection from buildings, objects and people.
Guidance and manufacturer's declaration – Immunity Emissions
Compliance
the EN 60601-1-2
3Vrms 150kHz to V
1
80Mhz
(for non life-
3V/m 80MHz to E
1
2.5GHz
(for non life-
Separation distance from the frequency transmitter (m)
80 MHz to 800 MHz
] d = [12/E
P
1
0,12
0,38
1,2
3,8
12
Electromagnetic environments - guidance
level
= 3 V rms Portable and mobile RF communication equipment,
including cables, should be used no closer to any part of the
device, than the recommended separation distance
calculated from the equation applicable to the frequency of
the transmitter.
= 3 V / m
Recommended separation distance
d = [3.5 / V ]
1
d = [12 / E ]
1
d = [23 / E ]
1
Where P is the maximum output power rating of the
transmitter in Watt (W) according to the transmitter
manufacturer and is the recommended separation distance
in metres (m). Field strengths from fixed RF transmitters,
as determined by an electromagnetic site study of the site,
should be less that the compliance level in each frequency
range. Interference may occur in the vicinity of equipment
marked with the following symbol:
]
P
1
0,12
0,38
1,2
3,8
12
17
P rom 150kHz to 80MHz
from 80 MHz to 800MHz
P
P from 800 MHz to 2.5 GHz
800 MHz to 2.5 GHz
d = [23/E ]
P
1
0,23
0,73
2,3
7,3
23
GB