Makita DSP600 Manual De Instrucciones página 16

Blade guard cleaning
When changing the circular saw blade, make sure to
also clean the blade guard of accumulated sawdust as
discussed in the Maintenance section. Such efforts do
not replace the need to check guard operation before
each use.
Connecting a vacuum cleaner
Optional accessory
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Connect
a hose of the vacuum cleaner to the dust nozzle using
the front cuff 24.
► Fig.25: 1. Hose of the vacuum cleaner 2. Front cuff
24 3. Dust nozzle
OPERATION
CAUTION:
Be sure to move the tool forward
in a straight line gently. Forcing or twisting the tool
will result in overheating the motor and dangerous
kickback, possibly causing severe injury.
CAUTION:
Never approach any part of your
body under the tool base when section cutting,
especially at starting. Doing so may cause seri-
ous personal injuries. The blade is exposed under
the tool base.
NOTE: When the battery cartridge temperature is
low, the tool may not work to its full capacity. At this
time, for example, use the tool for a light-duty cut for
a while until the battery cartridge warms up as high
as room temperature. Then, the tool can work to its
full capacity.
Section cutting (ordinary sawing)
► Fig.26
Hold the tool firmly. The tool is provided with both a front
grip and rear handle. Use both to best grasp the tool.
If both hands are holding saw, they cannot be cut by
the circular saw blade. Set the base on the workpiece
to be cut without the circular saw blade making any
contact. Then push in the lock-off button and pull the
switch trigger. Wait until the circular saw blade attains
full speed. Now press down the saw head slowly to the
preset depth of cut and simply move the tool forward
over the workpiece surface, keeping it flat and advanc-
ing smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and
your speed of advance uniform. If the cut fails to prop-
erly follow your intended cut line, do not attempt to turn
or force the tool back to the cut line. Doing so may bind
the circular saw blade and lead to dangerous kickback
and possible serious injury. Release the switch, wait
for the circular saw blade to stop and then withdraw
the tool. Realign the tool on new cut line, and start
cut again. Attempt to avoid positioning which exposes
operator to chips and wood dust being ejected from the
saw. Use eye protection to help avoid injury.
Guide rail
Optional accessory
Place the tool on the rear end of guide rail. Turn two
adjusting screws on the tool base so that the tool slides
smoothly without a clatter. Hold both the front grip and
rear handle of the tool firmly. Turn on the tool, press down
the tool to the preset cutting depth and cut the splinter-
guard along the full length with a stroke. Now the edge of
the splinterguard corresponds to the cutting edge.
► Fig.27: 1. Adjusting screws
When bevel cutting with the guide rail, use the slide
lever to prevent the tool from falling over.
Move the slide lever on the tool base in the direction of arrow
so that it engages the undercut groove in the guide rail.
► Fig.28: 1. Slide lever
Sub base (Guide rule)
Optional accessory
By using the sub base as a guide rule, you can perform
extra-accurate straight cuts. Loosen the clamping
screws and slide the sub base out from the tool then
insert it upside down.
► Fig.29: 1. Clamping screw 2. Sub base
Simply slide the fence of the sub base snugly against
the side of the workpiece and secure it in position with
the clamping screws. It also makes repeated cuts of
uniform width possible.
► Fig.30: 1. Clamping screw 2. Sub base
Plunge cutting (Cutting-out)
WARNING:
observe the following instructions.
► Fig.31: 1. Rear edge of tool base 2. Fixed stop
When using the tool without guide rail, place the tool on
the workpiece with the rear edge of tool base against a
fixed stop or equivalent which is devised by an operator.
When using the tool with guide rail, place the tool on the
guide rail with the rear edge of tool base against a fixed
stop or equivalent which is clamped on the guide rail.
Hold the tool firmly with one hand on the front grip and
the other on the tool handle. Then push in the lock-off
button and turn the tool on and wait until the blade
attains full speed. Now press down the saw head slowly
to the preset depth of cut and simply move the tool
forward to the desired plunge position.
NOTE: The markings on the side of the blade guard
show the front and rear cutting points of the saw blade
at the maximum cutting depth when using the guide rail.
► Fig.32: 1. Front cutting point 2. Rear cutting point
Guide device
Optional accessory
Use of the bevel guide allows exact miter cuts with
angles and fitting works.
Use of the clamp ensures firm hold of workpiece on the
table.
16 ENGLISH
To avoid a kickback, be sure to