Sammic ES-100 Manual De Instrucciones página 5

Escurridor de verduras

Ocultar thumbs Ver también para ES-100:

Manual de instrucciones (17 páginas)

página de 16

/ 16
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

load balance. If in any event it detects an inci-

dent of this type the machine stops and the

"unbalanced " (Diag. A e) pilot light comes on

and a sound warning is emitted.

Slow speed cycle (snail key pilot light Diag. A f

switched on).

With the cover closed, when the cycle start key is

pressed (Diag. A 3) the cycle starts and is divided

into two parts:

- Basket locking. The machine performs a first

short start up to lock the basket in its bracket.

- Then the machine starts up again and once the

slow speed has been attained it operates until

the end of the time cycle and it automatically

stops emitting and end of cycle beep.

Throughout this process the control continues

to monitor the status of the load balance. If in

any event it detects an incident of this type the

machine stops and the "unbalanced " (Diag. A

e) pilot light comes on and a sound warning is

emitted.

With either of the two options, if the cover is ope-

ned, the cycle stops. If wee press the cycle start

key (Diag, A 3) again the cycle starts from the

beginning.

Loading of the machine and start up. Operation

mode.

WARNING:

Before using the machine for the first time, clean

the basket with (lukewarm) soapy water, rinse

and leave to dry. Use a damp cloth to clean the

rest of the machine.

To fill the machine:

a) Raise the machine's cover.

b) For optimal drainage fill the basket to ¾ of its

capacity, preferably outside the machine in

order to prevent the drain from becoming clog-

ged up.

c) The heads of lettuce must be inserted clean

into the centrifuging (spinning) basket.

Remove any damaged or blackened leaves.

They must not be pressed when putting into

the basket.

d) Fit the basket to the machine's shaft, ascertai-

ning that it is in position by giving the basket a

¼ turn.

e) Shake the basket to balance the load as much

as possible.

f) Close the cover, select the desired cycle and

press the cycle start (Diag. A 3) key.

IMPORTANT: If the basket contains more than

7 kg of product, only use the slow speed

option (pilot light Diag. A f on).

g) At the end of the centrifuging cycle the machi-

ne automatically stops and emits an acoustic

signal.

h) To increase the machine's yield use two bas-

kets. To prevent idle times the basket filling

and emptying operations should be carried out

while the cycle is underway.

Capacity

ES-200: 10-14 heads of lettuce or 12 kg of vege-

tables.

ES-100: 5-7 heads of lettuce or 6 kg of vegeta-

bles.

For product cleaning and preservation

a) Washing and rinsing:

-Properly separate and choose the leaves.

Important: Remove the bad leaves.

- Wash and soak in very cold water(4-5 ºC)

- Properly rinse the lettuce leaves.

b) Centrifuging:

- Eliminate the washing and soaking water.

c) Preservation:

- Do not cut the leaves to pieces until needed.

Keep chilled between 0 and 5ºC.

Cleaning the drainage machine:

For the daily cleaning of the machine:

a)The basket must be cleaned outside the

machine right after its use. Use hot water and

any ordinary detergent for domestic dish-was-

hing. It must be rinsed with plenty of hot water.

Finally use a clean cloth with ethyl alcohol to

clean the areas that come into contact with

food.

b)IMPORTANT: Do not clean the inside or the

outside of the machine with a direct water jet or

a pressurised hose. Use a damp cloth and any

usual detergent. Do not use bleach, harsh che-

micals or metal scrubbers.

MAINTENANCE AND PRESERVATION

Before undertaking any cleaning, inspection or

repair work on the machine, the machine must

be unplugged from the mains.

State of the shock absorbers:

Every so often check the state of the shock

absorbers. To do this, with the basket fitted, flex

the basket and ascertain that movement is even

in all directions. If this is not the case, one of the

shock absorbers may be damaged. For repair

contact an authorised technical service. It is also

recommended that annually a technician of the

authorised technical service should visually ins-

pect the shock absorbers.

Condition of the wheels:

Every so often the condition of the wheels should

be visually inspected and the proper operation of

the brakes should be verified.

Condition of the drainage:

Before each use check that the machine's drai-

nage pipe is free of blockage that may prevent

the water from being drained out of the machine.

Operating incidents:

Often the machine shuts down due to load imba-

lances:

- Try to properly distribute the load and shake the

basket in each cycle.

- Verify the condition of the shock absorbers.

These may be damaged.

- Verify the condition of the wheels. They may be

damaged.

- Verify the overall condition of the machine.

Something maybe loose and lead to an increa-

se in the machine's vibration.

The machine does not start:

- Verify that electric current reaches the control

panel.

- Verify that the keyboard is properly connected

to the control panel.

Status of the door detector:

If the machine does not start when you the press

the "cycle start-up" button (Diag. A-3) and the

cover is down, but the pilot light related to this

button (Diag. A "d") starts to blink, this means that

there is a problem with the magnetic detector of

the door or with its magnet.

Motor thermal switch:

If the "alarm pilot light" (Diag. A g) flashes quickly

and the panel emits a beep as fast as the flas-

hing of the pilot light, this means that the motor's

thermal protector has been triggered. This

means that there is some problem with the

motor, that the axle is jammed, the basket is

caught on something...

Verification of the keyboard:

- With the general switch on every time a key is

pressed on the control panel a "beep" is emitted

and the related function is performed.

Listing of alarms pertaining to the electronics

board:

Occurs when the "alarm pilot light" (Diag. A g) is

on and another pilot light is flashing. Therefore: