Idiomas disponibles
Idiomas disponibles
met
na
aa
geek.
¿min
3 séi
"furs
st
+
A
SÉ lt
Zn
d m
Ee?
fa: =
OR YOUR OWN SAFETY READ INSTRUCTION MANUAL BEFORE OPERATING SAW.
+ Wear eye protection
e Use splash hood for every operation for which it can be used
+ Unplug saw before servicing, when changing cutting wheels, and cleaning
+ Use Saw only with smooth—edge Blade (Continuous Rim) free of openings and grooves
e Replace damaged cutting wheel before operating
es Do not fill water tray above water fill line
e Do not expose to rain, or use in damp locations
USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord,
be sure to use a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in
line voltage, resulting in loss of power and overheating. Table below shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier
the cord.
Table 1
Volts
Total length of cord in feet
|
120V
25ft.
100ft.
Ampere Rating
240V
Soft.
200ft.
AWG
Not More Than
a
EE
6
18
16
16
10
18
16
14
12
12
16
16
14
12
. Not Recommended
STATE-OF-THE-ART FEATURES
UNPACKING, ASSEMBLY & SET-UP
e (2) motor speeds: 1750 & 2450
RPM
allow operator to
CAUTION: FOLLOW ALL OF THE ASSEMBLY &
change
RPM
to accommodate
different blades or profile
INSTALLATION INSTRUCTIONS CAREFULLY BEFORE
wheels and to cut a wide array of materials.
CONNECTING THE SAW TO A POWER SOURCE, OR
Automatic thermal overload protection protects saw from
TURNING THE MOTOR ON.
power surges and motor overheating.
Carefully open the container and remove all saw components
and packing materials.
Automatic power kill switch shuts off motor if power is
interrupted. Easy ON/OFF Toqqle switch.
The contents of the container are as follows:
e Fiberglass impregnated
polycarbonate water tray is long-
e Motor Assembly
e Blade Guard
e Saw Stand
lasting and will not crack or split.
e 10" Diamond Blade
e Water Pump ` e Owner's Manual
,
i
:
+ Saw Frame
i
e Drain Plug
e 2 Wrenches
e Easily converts from a stand toa tabletop configuration.
Plastic Water Tray
e Miter Block
e Hex Key
e Cutting Table
Rip Guide
e 4 bolts and washers for
Tray handies front and back for easy one-man moving.
use with
optional
Cutting Table Extension
Cutting table adjusts for 14" tile diagonal rip cuts with
o
greater stability.
Ensure that you have checked each item with the exploded
e Blade shaft lock keeps blade in place for easy blade
a
ER
discarding the container or
changes.
ELECTRICAL/MOTOR SPECIFICATIONS
SAW SET-UP `
e Horsepower: 2HP
|
1.
If you are using the optional folding support stand, see
ie EE 50 cycle, single phase
the assembly instructions on page 8.
©
Amps:
¢ RPM Variable: 1750-2450
2.
Place the stand on a solid, level surface.
e Arbor: 5/8"
|
Place the saw frame (Part 620-1009) on the optional
folding stand, with the vertical post of the frame toward
the rear of the stand.
e Connect saw as close as possible to power source
3.
EXTENSION CORDS: When using an extension cord, ensure all cords
are no smaller than #12 gauge, rated at a 20-amp minimum, and
4. lf you are not using the folding stand, set the saw frame
equipped with 3-prong plugs. Use of anything smaller may result in
x
overheating or burn out of the motor. It is recommended to have an
on a solid, flat warkbench or table.
electrician check the voltage at the saw motor to ensure proper voltage
to run the saw efficiently and safely.
étre
vrac
ns
pce Pinan
dede
beten
ENK
d'en
Ka gage
Bin ay ad
SE
A
A
RARA
ana
du A
a
ió
dd
a
Hipo
man
tobe,
ini
a
aia
apa
el
dd Kn
