Idiomas disponibles
Idiomas disponibles
Inserting filters
Note: For circulating-air mode, insert the odour fil-
ters.
For air extraction mode, insert the acoustics filters.
Observe the filters' air flow direction.
1.
Insert two of the filters into the left and right of the
2.
appliance, and slide them forwards.
→ Fig.
46
Insert the other filters into the left and right of the
3.
appliance.
→ Fig.
47
Inserting grease filters
Insert the grease filter.
▶
→ Fig.
48
Establishing the connection to the power
supply
Observe the connection data on the rating plate.
1.
For 3 N, connect the cable to the mains socket in
2.
accordance with the figure.
→ Fig.
49
For 2 N, connect the cable to the mains socket in
3.
accordance with the figure.
→ Fig.
50
For 1 N, connect the cable to the mains socket in
4.
accordance with the figure.
→ Fig.
51
For 2 L/2 N, connect the cable to the mains
5.
socket in accordance with the figure.
→ Fig.
52
Note the colours of the cables.
6.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
– GY: Grey
If required, arrange the supplied wire end ferrules
7.
differently depending on the type of connection.
To connect two cables, if required, use a wire end
8.
ferrule.
Shorten the wires.
‒
Remove the insulation.
‒
Checking the function
Switch on the appliance.
1.
If
,
or
lights up, the appliance is not
2.
connected correctly. → "Checking and correcting
the electrical connection", Page 25
If no faults appear in the appliance's display, use
3.
the operating instructions to check that the ventila-
tion is working.
Checking and correcting the electrical connection
Disconnect the appliance from the power supply.
1.
Check whether the connection to the appliance
2.
and the building-side connection correspond to
the connection diagram in these installation in-
structions. → "Preparing the electrical connec-
tion", Page 22 → "Establishing the connection to
the power supply", Page 25
For 3 N, observe the following figure.
3.
→ Fig.
53
For 2 N, observe the following figure.
4.
→ Fig.
54
For 1 N, observe the following figure.
5.
→ Fig.
55
Sealing crevices
Requirement: You must carry out a function test be-
fore sealing the joint.
Seal the gap around it using suitable, heat-resist-
1.
ant silicone, e.g. Novasil® S70 or Ottoseal® S70.
→ Fig.
56
Unsuitable silicone adhesive causes permanent
discoloration to natural stone worktops.
Use the smoothing agent recommended by the
2.
manufacturer to smooth the crevice.
Observe the usage instructions for the silicone ad-
3.
hesive.
Leave the silicone adhesive to dry for at least 24
4.
hours.
The drying time depends on the ambient temper-
ature.
Do not operate the appliance until the silicone has
5.
dried completely.
Switching the display for air extraction
mode
If required for the air extraction mode and the air
1.
recirculation mode, change the display of the elec-
tronic control in the basic settings.
Observe the basic settings section in the instruc-
2.
tion manual.
Removing the appliance
ATTENTION!
Tools may damage the appliance frame.
Do not prise out the appliance from above.
▶
Disconnect the appliance from the power supply.
1.
Remove the exhaust air duct or undo the circulat-
2.
ing-air connections.
Remove the silicone joint.
3.
Push out the appliance from below.
4.
fr
Contenu de la livraison
Après avoir déballé le produit, inspectez toutes les
pièces pour détecter d'éventuels dégâts dus au
transport et pour vous assurer de l'intégralité de la li-
vraison.
→ Fig.
1
Code QR vidéo concernant l'installation
Vous trouverez ici le code QR pour la vidéo concer-
nant l'installation.
→ Fig.
2
Dimensions de l'appareil
Vous trouverez ici les dimensions de l'appareil
→ Fig.
3
Cotes d'encastrement coudes de conduit
plat
Vous trouverez ici une vue d'ensemble des cotes
d'encastrement des coudes de conduit plat.
Vue latérale :
→ Fig.
, → Fig.
, → Fig.
4
5
Vue de face :
→ Fig.
7
Variantes d'installation
Vous trouverez ici une vue d'ensemble des diffé-
rentes variantes d'installation.
Filtre anti-odeurs et adaptateur pour mode
recirculation de l'air :
→ Fig.
8
6
25
