Dräger HPS 3500 Instrucciones De Uso página 9

3.6 Explanation of type-identifying markings
and symbols
3.6.1 Helmet
1 2 3 4 5 6
12 11 10 9
1 Notified body
2 Optional requirements (marked with ***)
3 Sizes
4 Refer to instructions for use
5 Manufacturer
6 Distributor
7 Product description
8 Product name
9 Serial number
10 Country and date of manufacture
11 Reference standards
12 CE mark
4 Use
4.1 Prerequisites for use
Any improper use of the helmet beyond its intended use or the
applicable laws and regulations may expose the user to
personal harm.
In order to provide adequate protection, this helmet must be
adjusted to the head size of the user.
For your own safety, familiarize yourself with the adjustment
systems before using the helmet. Make several adjustments
and fasten and unfasten the retention system several times so
that these actions become instinctive.
4.2 Preparation for use
WARNING
!
Risk of injury!
The protective effect of the helmet is achieved only
when the helmet fits perfectly, wearing height, harness
and support ring are properly adjusted and the chin
strap is closed.
Only wear the helmet when it is fully assembled. All
attachments must be properly secured to the helmet.
Do not wear removable parts separately.
Dräger HPS 3500
7
8
02431261
4.2.1 Adjusting the height
Adjust the helmet in height by changing the depth of the hairnet
as follows:
1. Release the rear tabs of the hairnet fastened with hook-
and-loop fastener and slide them in the slots on the
retainer.
4.2.2 Adjusting the circumference
INFO: The helmet is supplied with the size retainer fully
extended. For proper adjustment follow the sequence
described below.
1. Put on the helmet and then adjust the size using the wheel.
2. For optimal adjustment, it is advisable to push down on the
helmet with one hand and then make the adjustment with
the other hand. The size adjustment system also acts on
the neck straps.
3. Pull the two straps (see figure 1, item 1) that join the chin
strap to the adjustment system only during the first
adjustment.
4.2.3 Adjusting the retention system
First use
Chin strap:
1. Adjust in height as described in chapter 4.2.1.
2. Put on the helmet.
3. Adjust the size as described in chapter 4.2.2.
4. Fasten the buckle.
5. Slide the adjustment strap (see figure 2, item 1) in the
adjustment crosspiece of the system (item 2).
6. Again pull the adjustment strap so that the system adjusts
correctly.
7. If you cannot achieve the correct adjustment, act on the
adjusters (see figure 3, item 3) positioned on either side of
the chin strap and lengthen or shorten the strap.
Regular use
Chin strap:
1. Fasten the chin strap with the buckle.
Size adjustment:
1. Adjust as described in chapter 4.2.2.
4.2.4 Attaching the safety goggles (optional)
Attach the safety goggles with silicone cord as follows (see
figure 4).
1. Insert one of the ends of the silicone cord from the outside
into the hole (item 1).
2. Repeat with the other end of the silicone cord on the other
side of the helmet.
3. Pull on both ends of the cord evenly so that the cord sits on
the helmet rim.
4. Pull one end of the silicone cord first through one hole on
the inside of the safety goggles support (item 3). Then pull
it back through the other hole (item 4).
5. Continuing with the same end, pull the silicone cord
through the hole in the helmet shell (item 1) again.
6. Pull the same end of the silicone cord through the hole in
the middle of the helmet rim (item 2) and securely fasten it
by making a single knot (detail A).
7. Repeat steps 4-6 with the other end of the silicone cord.
Use
9