Dräger HPS 3500 Instrucciones De Uso página 10

Use
Attach the safety goggles with the elastic band as follows (see
figure 5).
1. Starting from the inside of the safety goggles, pull one end
of the elastic band out through the narrow slit of the safety
goggles support. Pull the elastic band back in through the
wide slit. This fixes the elastic band to one side of the safety
goggles.
2. Slide the other end of the elastic band through the oblique
slit in the helmet shell (item 1).
3. Slide the elastic band around the rear of the helmet. Pull
the band through the oblique slit on the other slide. making
sure that it sits on the elevated part of the helmet above the
rim as seen in figure 5.
4. Fix the end of the elastic band to the safety goggles as
described in step 1.
Attach the safety goggles with elastic band and fast connection
system (QuickConnect) as follows (see figures 7-11).
1. Check that the safety goggles are positioned correctly
(figure 7).
2. Insert one of the fast couplings into one of the oblique slits
on the helmet shell (see figure 8, item 1).
3. Position the tooth of the fast coupling so that it rests on the
edge of the helmet shell (see figure 8, item 2).
4. Push the coupling (see figure 9, item 3) until a "CLICK" is
heard (see figure 9, item 4.
5. Make sure that the attachment system of the fast coupling
is correctly connected to the helmet shell (see figure 10).
6. Repeat steps 2-5 on the other side of the helmet (see
figure 11).
When the safety goggles are used with the elastic band or with
the quick connectors, the pressure of the safety goggles on
your face can be adjusted using the ends of the elastic band
that protrude from the retainers.
If you do not want to use the safety goggles, push it up onto the
helmet.
When the safety goggles are used with the fast connection
system, you can remove them by pushing the teeth of the
connection system.
4.2.5 Attaching the side lamp (optional)
The lamp holder is fitted on the left or right of the helmet shell
on the dedicated adaptors.
1. To use the lamp, fit the holder (see figure 12, item 1) in the
slide of the adaptor (item 2).
2. Fit the lamp (see figure 14, item 3) in the holder (item 1).
The lamp can be used in two positions:
facing down (see figure 15)
 
facing up (see figure 16)
 
4.2.6 Attaching the front lamp (optional)
The front lamp adapter (see figure 17, item 2) is fixed to the
interface on the front of the helmet shell and is compatible only
with specifically designed front lamps.
1. Position the front lamp with the lamp adapter (see
figure 17, item 1) on the front lamp interface from the top
(see figure 18).
2. Slide the lamp down until the adapter clicks into the front
lamp interface (see figure 19).
3. Adjust the position of the lamp (see figures 20+21, item 2)
10
4. To remove the lamp (see figure 22) pull the lever (item 3)
on the lamp adapter until the adapter detaches from the
interface. Slide the front lamp with the lamp adapter
upwards and remove it from the front lamp interface.
Further details will be available in the instructions for use
provided with the accessories.
4.2.7 Attaching the earmuffs (optional)
1. To fasten the earmuffs, fit the fastening supports (see
figure 23, item 2) on the connectors (item 1) provided on
the helmet shell.
2. Pull the earmuffs down over the ears to use them or push
them up if you do not want to use them.
3. To push up the earmuffs onto the helmet shell, first pull
them off your ears until you hear a click and then turn them
upward and lock them into place by pressing on the
earmuffs.
4. To remove the earmuffs, press on the locking point (see
figure 24, item 3) of the fastening support (item 2).
Further details will be available in the instructions for use
provided with the accessories.
4.2.8 Attaching the mesh visor/transparent visor
(optional)
INFO: To fit these accessories, you must have fitted the
earmuffs or the relative supports.
This accessory is not compatible with the safety goggles.
1. Clip the visor onto the fastening clips (see figure 25, item 1)
in the fastening supports (item 2).
Once fastened, the visor can be adjusted to two positions:
up (see figure 27)

down (see figure 26)

2. To remove the visor, pull it out of the fastening clips.
Further details will be available in the instructions for use
provided with the accessory.
4.2.9 Attaching the neck guard (optional)
1. Identify the two snap fasteners on the back of the helmet
(see figure 28, item 1).
2. Remove the rubber protective caps on the snap fasteners
(see figure 29).
3. Connect the snap fasteners on the neck guard with the
snap fasteners on the helmet (see figure 30).
4. Attach the hook-and-loop straps of the neck guard to the
retainer of the helmet (see figure 31).
To remove the neck guard work in reverse order.
The neck guard can be used in two different ways:
Nape and shoulder protection:

Position the neck guard behind the neck and on the

shoulders with the side pieces folded back (see
figure 34).
Nape, shoulder, and throat protection:

Position the neck guard behind the neck and on the

shoulders with the side pieces tied around the throat
(see figure 35).
Further details will be available in the instructions for use
provided with the accessories.
Dräger HPS 3500