Cutting Height Adjustment; Using The Machine; Preparation; Safety Checks - GGP ITALY MP2 504 Serie Manual De Instrucciones

6.

USING THE MACHINE

The safety regulations to follow are
described in chap. 2. Strictly comply with these
instructions to avoid serious risks or hazards.
IMPORTANT For instructions regarding the engine
and the battery (if supplied), read the relevant manuals.
6.1

PREPARATION

Before starting to mow, it is necessary to carry
out several checks and operations to ensure you
can work efficiently and in maximum safety.
Place the grass mower in a stable
horizontal position on the ground.
6.1.1 Filling with oil and fuel
IMPORTANT The machine is supplied
without engine oil or fuel.
Before using the machine check for fuel and the oil
level (par. 7.2, par. 7.3). For refuelling and oil top-up
methods and precautions follow the instructions given
in (par. 7.2, par. 7.3) and in the engine handbook.
6.1.2 Preparing the machine before starting work
NOTE This machine can be used to mow lawns in a
number of different ways; before starting work, prepare
the machine based on how the lawn is to be mowed.
a. Preparation for grass cutting and
collection in the grass catcher:
• Type "I"
1. Insert the grass-catcher as indicated in the
diagram (fig. 10.A). Position the side pins
in the guides on the base of the handle (fig.
10.B) and push the grass-catcher forwards
until you hear it click into place (fig. 10.C).
• Type "II"
1. Lift the rear discharge guard (fig. 10.D)
and fasten the grass catcher correctly as
shown in the illustration (fig. 10.E).
b. Preparation for mowing and grass
rear discharge onto the ground:
• Type "I"
1. Remove the grass catcher.
2. Lift the rear discharge guard (fig. 11.A) and fit the
rear discharge chute (fig. 11.C) into the relative
holes, making sure it is securely in place.
3. On models with a side discharge: make sure that
the side discharge guard (fig. 11.D) is lowered.
To remove the rear discharge chute:
1. Lift the rear discharge guard (fig. 11.A);
2. Lift the rear discharge chute and
release it from the holes (fig. 11.C).
• Type "II"
1. Remove the grass catcher and check
that the rear discharge guard (fig. 11.A)
maintains its lowered position.
c. Preparation for mowing and mulching:
1. Lift the rear discharge guard (fig. 12.A) and fit the
chute cap (fig. 12.B) in the discharge opening.
2. On models with a side discharge: make sure that
the side discharge guard (fig. 11.D) is lowered.
To remove the chute cap:
1. Lift the rear discharge guard (fig. 12.A);
2. Remove the chute cap (fig. 12.B).
d. Preparation for mowing and grass
side discharge onto the ground:
1. Lift the rear discharge guard (fig. 12.A) and fit the
chute cap (fig. 12.B) in the discharge opening.
2. Lift the side discharge guard (fig. 13.A)
3. Insert the side discharge chute (fig. 13.E).
4. Close the side discharge guard (fig.
13.A) so that the side discharge chute
(fig. 13.E) is locked in place.
To remove the side discharge chute:
1. Lift the side discharge guard (fig. 13.A);
2. Release the side discharge chute (fig. 13.E).
To remove the chute cap:
1. Lift the rear discharge guard (fig. 12.A);
2. Remove the chute cap (fig. 12.B).
6.1.3

Cutting height adjustment

Adjust the cutting height as indicated in (par. 5.7).
6.1.4 Adjusting the handle height
The handle height can be adjusted to 3 different
positions, as marked on the handle base (fig. 14.A).
It is also possible to fold the handle to the
closed position from the working position.
Do this when the cutting means is stationary.
To change the handle height, pull both levers on the
handle sides (fig. 14.B), and hold them in position.
Move the handle carefully to the desired
height and release the two levers.
6.2

SAFETY CHECKS

Run the following safety checks and check that the
results correspond to those outlined on the tables.
Always carry out the safety checks before use.
EN - 6