Idiomas disponibles
Idiomas disponibles
22 | English
the wheel to climb out or kick out. The wheel may either
jump toward or away from the operator, depending on direc-
tion of the wheel's movement at the point of pinching. Abras-
ive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
Maintain a firm grip with both hands on the power tool
u
and position your body and arms to allow you to resist
kickback forces. Always use auxiliary handle, if
provided, for maximum control over kickback or
torque reaction during start-up. The operator can con-
trol torque reactions or kickback forces, if proper precau-
tions are taken.
Never place your hand near the rotating accessory.
u
Accessory may kickback over your hand.
Do not position your body in the area where power
u
tool will move if kickback occurs. Kickback will propel
the tool in direction opposite to the wheel's movement at
the point of snagging.
Use special care when working corners, sharp edges,
u
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
Do not attach a saw chain woodcarving blade, seg-
u
mented diamond wheel with a peripheral gap greater
than 10 mm or toothed saw blade. Such blades create
frequent kickback and loss of control.
Safety warnings specific for grinding and cutting-off
operations:
Use only wheel types that are specified for your power
u
tool and the specific guard designed for the selected
wheel. Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
The grinding surface of centre depressed wheels must
u
be mounted below the plane of the guard lip. An im-
properly mounted wheel that projects through the plane
of the guard lip cannot be adequately protected.
The guard must be securely attached to the power tool
u
and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.
The guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel and
sparks that could ignite clothing.
Wheels must be used only for specified applications.
u
For example: do not grind with the side of cut-off
wheel. Abrasive cut-off wheels are intended for peri-
pheral grinding, side forces applied to these wheels may
cause them to shatter.
Always use undamaged wheel flanges that are of cor-
u
rect size and shape for your selected wheel. Proper
wheel flanges support the wheel thus reducing the pos-
sibility of wheel breakage. Flanges for cut-off wheels may
be different from grinding wheel flanges.
1 609 92A 9AU | (09.04.2024)
Do not use worn down wheels from larger power tools.
u
A wheel intended for larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
When using dual purpose wheels always use the cor-
u
rect guard for the application being performed. Failure
to use the correct guard may not provide the desired level
of guarding, which could lead to serious injury.
Additional safety warnings specific for cutting-off
operations:
Do not "jam" the cut-off wheel or apply excessive
u
pressure. Do not attempt to make an excessive depth
of cut. Overstressing the wheel increases the loading
and susceptibility to twisting or binding of the wheel in
the cut and the possibility of kickback or wheel breakage.
Do not position your body in line with and behind the
u
rotating wheel. When the wheel, at the point of opera-
tion, is moving away from your body, the possible kick-
back may propel the spinning wheel and the power tool
directly at you.
When the wheel is binding or when interrupting a cut
u
for any reason, switch off the power tool and hold it
motionless until the wheel comes to a complete stop.
Never attempt to remove the cut-off wheel from the
cut while the wheel is in motion otherwise kickback
may occur. Investigate and take corrective action to elim-
inate the cause of wheel binding.
Do not restart the cutting operation in the workpiece.
u
Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
Support panels or any oversized workpiece to minim-
u
ize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
Use extra caution when making a "pocket cut" into ex-
u
isting walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects
that can cause kickback.
Do not attempt to do curved cutting. Overstressing the
u
wheel increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility of
kickback or wheel breakage, which can lead to serious in-
jury.
Safety warnings specific for sanding operations:
Use proper sized sanding disc paper. Follow manufac-
u
turers recommendations, when selecting sanding pa-
per. Larger sanding paper extending too far beyond the
sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
Safety warnings specific for wire brushing operations:
Be aware that wire bristles are thrown by the brush
u
even during ordinary operation. Do not overstress the
Bosch Power Tools
