IMPORTANT: Use the following chart to help determine the correct Throat Plate and Sleeve
Drums to use with each Sanding Sleeve.
Throat plate chart
Sanding Sleeve
Sleeve Drum (31)
(25)
13mm (1/2")
N/A
19mm (3/4")
Small
26mm (1")
Medium
38mm (1-1/2")
Large
51mm (2")
Very Large
Notes
• All the Sanding Sleeves (25), except the smallest 13mm (1/2"), fit over a matching Sleeve
Drum (31).
• When the sanding sleeve is worn at the bottom only it is possible to turn it upside down and
maximise its service life by using the remaining grit
• If the sleeve rotates on the drum when switched on, the Spindle Nut (27) has not been
sufficiently tightened to compress the drum and therefore grip the sleeve.
• Ensure there is no contact between the Sanding Sleeve and the Table Insert before switching
the machine on.
IMPORTANT: Do not use a sanding sleeve that is too worn. This can lead to excessive heat
build-up and damage the rubber drum. Damaged rubber drums due to worn sanding sleeves
will not be covered under warranty.
IMPORTANT: Failure to use the correct Throat Plate (26) with its matching sanding sleeve
could result in pinched fingers or the workpiece being pulled down between the Throat Plate
and the sanding sleeve.
The sanding sleeve should fit snugly into the central cut-out of the Throat Plate.
Tilting the Table
The Tilting Table (16) can be tilted up to 45° this allows easy chamfering as well other edge
work
1. Loosen the 2 Table Angle Knobs (8 & 19) on both sides of the table
2. Move the table to the required angle position using the Table Angle Gauge (9). There are
click-stop Table Angle Notches (10) at common angle positions (0°, 15°, 22.5°, 30° & 45°)
3. Lock the 2 Table Angle Knobs to secure the table at the required position
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as
well as suitable gloves, when working with this tool.
WARNING: ENSURE gloves and clothes worn do not have loose threads that could get
caught by the rotating spindle and drag your hand or head into the rotating spindle causing
severe injury. It is recommended to wear gloves that are not fabric based.
Switching on and off
Note: Ensure there is no contact between the Sanding Sleeve and the Throat Plate or Sanding
Belt and table surface before turning the machine on.
•
To turn the spindle sander on pull out the ON/OFF Switch (12) which hinges at the top
•
To turn the spindle sander OFF, press in the ON/OFF Switch
Note: The ON/OFF Switch is designed that it can be easily pressed in to turn off quickly when
in the ON position.
IMPORTANT: To prevent operation by children remove the Switch Lock (13) by pulling away
from the ON/OFF Switch and store securely. Once the Switch Lock is removed the ON/OFF
Switch is non-functional so it is important the Switch Lock is not lost.
Sanding
WARNING: Do not sand metal with this sander. Sanding metal will cause sparks that may
ignite wood and dust particles on the sander or in the workshop
Note: The spindle and belt rotate in an anti-clockwise direction
1. Check the machine is mounted securely on the workbench
2. Wear appropriate safety equipment, including face mask and safety glasses, then switch
on the dust extraction system (if available)
3. Turn the sander ON and allow the motor to reach full speed
IMPORTANT: Feed the workpiece gradually, AGAINST the direction of rotation, onto the sanding
sleeve (Image D) or belt. Failure to do this could force the workpiece away from the sanding
sleeve or belt with risk of injury. Do not force the workpiece or apply excessive force.
4. Use the Workpiece Stop (3) when possible
5. When finished, turn off the machine and disconnect from mains power
Throat Plate (26)
Spindle Washer
(28)
13mm (1/2")
Small
19mm (3/4")
Medium
26mm (1")
Medium
38mm (1-1/2")
Medium
51mm (2")
Large
Accessories
• A range of accessories and consumables, including sanding sleeves and belts are available
from your Triton stockist. Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: Ensure the tool is switched off and the plug is removed from the power point
before making any adjustments or carrying out maintenance.
•
Any damage to this tool should be repaired and carefully inspected before use, by qualified
repair technician
•
Have your power tool serviced by a qualified repair technician using only identical
replacement parts. This will ensure that the safety of the power tool is maintained
General Inspection
Regularly check that all the fixing screws are tight. They may vibrate loose over time.
Power Cord Maintenance
If the supply cord needs replacing, the task must be carried out by the manufacturer, the
manufacturer's agent, or an authorised service centre in order to avoid a safety hazard.
Cleaning
1. Remove dust and dirt regularly. Frequently blow or vacuum dust away from all sander
parts and the motor housing
2. Periodically remove the table insert and lower washer from the spindle and remove any
dust accumulation in the table insert area
3. Re-lubricate all moving parts at regular intervals
4. Never use caustic agents to clean plastic parts
Do not use cleaning agents to clean the plastic parts of the tool. A mild detergent on a damp
cloth is recommended. Water must never come into contact with the tool.
Brush Replacement
•
Over time the carbon brushes inside the motor may become worn
•
Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
•
To replace the brushes;
1. Place the sander carefully on its side, and remove the screws that secure the base cover
to allow access to the motor
2. Carefully clean inside if there is any accumulated wood dust or chippings by the base
cover
3. Remove the 2 screws that secure the brush cover (arrowed in Image E) and remove cover
4. Carefully remove brush assembly (Image F)
5. Disconnect wire attached to brush assembly and remove brush
6. Fit replacement brush and reconnect wire
7. Replace motor brush assembly ensuring small leg is correctly in place (arrowed in Image
F)
8. Refit brush cover and refit screws
9. Repeat these Steps 3–8 with the other brush assembly. It is important to always replace
brushes in pairs.
10. Re-install and tighten base plate.
Alternatively, have the machine serviced at an authorised service centre
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: tritontools.com/en-GB/Support
Address:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
•
Store this tool carefully in a secure, dry place out of the reach of children. If the tool
is permanently set up in a workshop or garage ensure access is restricted to prevent
children operating the tool.
EN
9