Endress+Hauser Smartec CLD132 Manual De Instrucciones página 85

Smartec CLD132
Function group
CALIBRATION
C
MEAS. VALUE DISPLAY
Conductivity
and
temperature (°C)
Function group
SETUP 1
A
Function group
SETUP 2
B
Function group
OUTPUT
O
Function group
ALARM
F
Function group
CHECK
(with software option
only)
P
Endress+Hauser
14 Anexo
Entry of
Calibration
calibration temperature
(if B1 = fixed)
InstF
25.0 C °
= installation factor
C1 (3)
–35.0 ... +250.0 C
Entry of
calibration temperature
Cellc
(if B1 = fixed)
= cell constant
C1 (2)
.
25.0 C °
–10.0 ... +150.0 C
Residual coupling
Airs = Airset
Start calibration
C1 (1)
current meas. value
Display of
conductivity and
temperature (°F)
Display of current
parameter set
(Remote parameter set
switching only)
Selection of display
Selection of operating mode
unit
cond = conductivity
ppm ; mg/l; %; TDS; none
conc = concentration
A1
Selection of temperature
Selection of
compensation type
temperature measurement
none
.
lin = linear
Pt100
NaCI = common salt
Pt1k (= Pt 1000)
Tab = table 1 ... 4
NTC30 (= NTC 30 kW
)
(>1 with software option
fixed
only)
B1
Selection of characteristic
sim = simulation
Selection of
current output
lin = linear
Out 1 ; Out 2
O1
Selection of Selection of
contact type unit for
alarm delay
Stead = steady contact
Fleet = fleeting contact F1 s ; min
PCS alarm setting
(live check)
Monitoring limit
0.3 % of mean value
off / 1h / 2h / 4h
over time entered
Entry of a value of
calibration solution
2.10 %/K
0.00 ... 20.00 %/K
° C131 C132
Entry of a value of
calibration solution
.
2.10 %/K
0.00 ... 20.00 %/K
C122
° C121
Display of
residual coupling value
-80.0 ... 80.0 µS
C112
C111
Display of
conductivity
Error display
(up to 10 errors)
Err ---
Selection of display format
(if A1 = conc)
X.xxx; XX.xx ; XXX.x; XXXX
A2 A3
Entry of a value
(if B2 = linear)
2.10 %/K
0.00 ... 20.00 %/K
B2 B3
Entry of
simulation value
current value
O2 (2)
0 ... 22.00 mA
O221
Selection of
current range
4-20 mA ; 0-20 mA
O2 (1)
O211
Entry of
alarm delay
0s ... 2000 s (min)
(depending on F2)
F3
F2
P1
Entry of correct
Display of calculated
conductivity value of installation factor
calibration solution
1.0
C133
current meas. value
0.10 ... 5.0
0.0 µS/cm ... 9999 mS/cm
Entry of correct
Display of calculated
conductivity value of
cell constant
calibration solution
.
-1
0.1 ... 9.99 cm
current meas. value
C123
0.0 mS/cm ... 9999 mS/cm
Display of Store
calibration results
calibration status
.
o.k.;
yes ; no; new
E--- C113
Display of
conductivity (uncompensated)
concentration
Selection of display
Entry of cell constant
unit
auto ; µS/cm; mS/cm; S/cm;
0.1 ... 6.3 ... 99.99 cm
µS/m; mS/m; S/m
A4
Entry of correct Temperature sensor
process temperature offset
(if B1 = fixed) (not if B1 = fixed)
25.0 °C Entry of actual temp.
–35.0 °C ... +250.0 °C –35.0 ... +250.0
B4
Entry of Entry of
0/4 mA value 20 mA value
0 µS/cm; 0 %; 0 °C 2000 mS/cm; 99.99 %;
entire meas. range 150.0 °C
entire meas. range
O212
Determination of Selection of
error current error number
22 mA 1
2.4 mA F4 1 ... 255
Anexo
C134
C124
C114
-1
A5
°C
B5
O213
F5
A0051368
85