Idiomas disponibles
Idiomas disponibles
Changing the collet
WARNING: Always disconnect the tool from the air supply before changing Collets (1) or
installing/removing accessories.
Note: This kit includes two sizes of Collet; one for accessories with large diameter shanks (1/4"), and
one for small diameter shanks (1/8").
1. Unscrew and remove the Collet Nut (7) from the Drive Shaft (6), using the Spanners (8)
2. Remove the Collet from the Drive Shaft and insert the Collet size you require
3. Replace the Collet Nut
Installing an accessory
WARNING: Always disconnect the tool from the air supply before changing Collets (1) or
installing/removing accessories.
1. Check the appropriate size Collet is fitted; fit correct size if necessary (see 'Changing the collet')
2. Insert the shank of the accessory as far into the Collet as it will go
3. Tighten the Collet Nut (7) by hand, then fit the two Spanners (8): the larger one on the Collet Nut,
the smaller on the Drive Shaft (6)
4. Tighten the Collet so that the accessory is securely fixed in place. Pull on the end of the accessory
to check
Operation
IMPORTANT: DO NOT allow the tool to run in 'idle rotation' for an extended period of time.
This will shorten its life.
1. Hold the tool firmly in the palm of your hand
2. Disengage the Safety Catch (2) and press the Trigger (3) to operate the tool
3. Allow the tool to reach full speed before bringing the accessory into contact with the workpiece
4. Release the Trigger to stop the tool
WARNING: Be aware that air tools may hold residual pressure after use. Always bleed air
pressure from the tool after shutting off air supply.
Accessories
• Accessories for this tool, including mounted grinding stones, rotary rasps, surface conditioning
pads and sanding and polishing tools, are available from your Silverline stockist. Spare parts can
be obtained from your Silverline dealer or www.toolsparesonline.com
Maintenance
WARNING: Always disconnect from the air supply and depressurise before cleaning or carrying
out any maintenance.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time.
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth
IMPORTANT: There is very little that can go wrong with your air tool and it should be noted that
when an air tool fails to work it is generally because the internal workings have corroded due to
dirty, wet air and failure to follow the instructions given below.
Daily maintenance procedure
1. Disconnect from the air supply
2. Pour 3-4 drops of oil into the air intake
3. Operate the machine at low speed to thoroughly lubricate all internal workings
• If the machine is in constant use or used for long periods at a time, the above procedure should
be repeated up to 3 times per day. Alternatively, fit an inline lubricator
• Use air tool oil. DO NOT UNDER ANY CIRCUMSTANCES USE NORMAL ENGINE OIL
• Failure to comply with the operating and maintenance instructions may invalidate the guarantee
Air Die Grinder Kit 15pce
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: www.silverlinetools.com
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
Hogeweg 39
5301 LJ Zaltbommel
The Netherlands
Disposal
• As with other power tools, air tools should not be disposed of with household waste
• Air tools may contain traces of tool oil and other lubricants and so must be recycled accordingly
• Contact your local waste disposal authority for information on the correct way to dispose of power
tools
silverlinetools.com
7
